Page 1 of 2

Fitting carpet

Posted: Mon Sep 15, 2008 12:06 pm
by Squiggle
Make sure your seat securing bolts are long enough to go through the new underfelt and carpet !!!

And don't fit it the day before a deadline to use the car ... and on a Sunday :x

Still feel it would been good if Newton Com' had pre-cut and reinforced the apertures for the pedals etc. The bit around the handbrake was and looks really good.

Just my humble opinion.

Posted: Mon Sep 15, 2008 1:07 pm
by ASL642
S, hope you're not still bent double after all that carpet fitting. Yes agree, bound holes would be good, but I suppose its not done as some people have their pedals in different places - Marina pedal boxes for instance. :wink:

Posted: Mon Sep 15, 2008 9:51 pm
by mike.perry
Managed to finish fitting the carpets on the MM at last. Trickiest bit was fitting the handbrake cable guides through the carpet and the prop shaft tunnel. That was a 2 person job. Would have been easier fitting carpets for the first time but replacement carpet clips had to line up with existing studs on the floor.
Had a moan to the Newton man at the nat. rally about the lack of cutouts. Something about l or r hand drive but they managed to get the heal pad on the correct side. Used my old carpets as templates.

Posted: Tue Sep 16, 2008 9:36 am
by Squiggle
regaliaqueen wrote:S, hope you're not still bent double after all that carpet fitting. Yes agree, bound holes would be good, but I suppose its not done as some people have their pedals in different places - Marina pedal boxes for instance. :wink:
Oh that's why my back is complaining :lol:

Pedals in different places......hmmm.....I thought the idea was, I was buying carpet that was specifically designed for an original MM. Enough said.

Looking forward to seeing Mike Perry's carpet. Still not sure what he means about two man job.......

Probably avoid letting him see my butchered job :oops:

Posted: Tue Sep 16, 2008 10:03 am
by ASL642
:D Dont forget to come and see me Saturday. :wink:

Posted: Tue Sep 16, 2008 10:21 am
by Squiggle
regaliaqueen wrote::D Dont forget to come and see me Saturday. :wink:
Ah. Would I forget to come and see you?

Or did you want to laugh at my carpet bodgejob.

Trying to decide on a route when I should be pouring something nourishing into my 'singing diff'...... It's quite melodic really.

Now I have carpet and underfelt, I can hear other noises that need attention now.

Will have to find the thread that suggests suitable 'goo'. Moly?

My Mum had an old Vauxall Viva and were advised to jack it up and feed a pair of tights into [moving wheels] the diff' to quieten it!

We decided not to :lol:

Could start a competition
Uses for a pair of tights on a Moggy Minor:
1 Fanbelt
2 Silence singing diff'
3 ?

Posted: Tue Sep 16, 2008 10:30 am
by ASL642
3. Keeping warm in the winter? You could always wear them! This depends on how efficient your heater is though. Upgraded Mini heater I've got defrosts the back doors on the traveller whilst slowly roasting your feet. :lol:

Posted: Tue Sep 16, 2008 10:51 am
by alex_holden
4. Wear them as a mask when robbing a bank to pay for the welding.

Posted: Tue Sep 16, 2008 11:00 am
by Squiggle
alex_holden wrote:4. Wear them as a mask when robbing a bank to pay for the welding.
Hmmm. No hope of a quick gettaway in my car tho' :wink:

Posted: Tue Sep 16, 2008 12:46 pm
by ASL642
Oh dear :roll:

Posted: Tue Sep 16, 2008 5:10 pm
by callyspoy
ha, my heater motor is super powerful, courtasy of a toyota supra/MR2 heater. but, just seems to bake your feet that little bit more! quite nice as i wear shorts in most weathers!
oh and...
5.use them as a steering wheel grip/embelisher. fishnets anyone...

Posted: Tue Sep 16, 2008 11:16 pm
by Kevin
my heater motor is super powerful, courtasy of a toyota supra/MR2 heater.
How easy was that to fit, how well did the screen pipeing match up and can you show a photo of it in place so we can see what it looks like.

Posted: Tue Oct 07, 2008 5:26 pm
by mike.perry
Squiggle.
The 2 man job was one person to screw the handbrake cable guide bolts threw the carpet and floor. The other person to lie under the car and hold a spanner between the propshaft and the propshaft tunnel to hold the nuts in place.
Now you've seen my carpets what do you think.

Posted: Tue Oct 07, 2008 6:02 pm
by alex_holden
mike.perry wrote:The 2 man job was one person to screw the handbrake cable guide bolts threw the carpet and floor. The other person to lie under the car and hold a spanner between the propshaft and the propshaft tunnel to hold the nuts in place.
This job is just about possible with one man under the car turning the nut and a pair of mole grips holding the bolt from inside the car. :)

Posted: Wed Oct 08, 2008 11:01 am
by Squiggle
mike.perry wrote:Squiggle.
The 2 man job was one person to screw the handbrake cable guide bolts threw the carpet and floor. The other person to lie under the car and hold a spanner between the propshaft and the propshaft tunnel to hold the nuts in place.
Now you've seen my carpets what do you think.
What do I think?

Hmmm..... I'll never get mine looking as good as yours..... :cry:

Need to wait till the next rally to 'borrow' 2 men for the '2 man job' :lol:

Posted: Tue Jan 27, 2009 9:44 pm
by Helenginger
Hi Guys - Just a thought, When I have new carpet fitted in the house I trim off-cuts to use as rugs to protect the carpet in "high-traffic" areas. I take the off-cuts to a carpet wholesaler where they bind the edges of the carpet to make the "rugs"presentable. I'm sure that other carpet wholesalers may do the same, but if it is of any use to anyone I can give the address of the guy I use in Northampton.

This may prove useful for binding around any non standard cut-outs that you may need to make. He keeps a massive stock of threads for the binding machine to match most carpet colours.

Just a thought,

Tom

Posted: Fri Jan 30, 2009 11:01 am
by Squiggle
Helenginger wrote:Hi Guys - Just a thought, When I have new carpet fitted in the house I trim off-cuts to use as rugs to protect the carpet in "high-traffic" areas. I take the off-cuts to a carpet wholesaler where they bind the edges of the carpet to make the "rugs"presentable. I'm sure that other carpet wholesalers may do the same, but if it is of any use to anyone I can give the address of the guy I use in Northampton.

This may prove useful for binding around any non standard cut-outs that you may need to make. He keeps a massive stock of threads for the binding machine to match most carpet colours.

Just a thought,

Tom
And a good thought, thank you.

Yes please as Northampton's accessible for me.

Need to get the front seats repaired/restitched too.
A stitch in time and all that.......

I think there's a guy called Baldisarie [sp?] in Bedford who repairs upholstery, I'll check it out. Would anyone like the details?

Unless anyone can recommend anyone else....

Posted: Fri Jan 30, 2009 3:43 pm
by Kevin
I like the sound of that
Rugs Presentable by Bald Sarnie :lol:

Posted: Fri Jan 30, 2009 5:39 pm
by Squiggle
Kevin wrote:I like the sound of that
Rugs Presentable by Bald Sarnie :lol:
I want some of what's he's on!

:lol: :lol:

Posted: Sat Jan 31, 2009 9:51 am
by Kevin
Squiggle wrote:
Kevin wrote:I like the sound of that
Rugs Presentable by Bald Sarnie :lol:
I want some of what's he's on!

:lol: :lol:
Pass your cup over then Chrissie