Blowing fuses… help!

Discuss anything Morris Minor related.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
mrs.smith2012
Minor Addict
Posts: 502
Joined: Wed Sep 17, 2025 6:19 pm
Location: Essex
MMOC Member: Yes

Re: Blowing fuses… help!

Post by mrs.smith2012 »

Okay, slight development… my fuses unexpectedly arrived today so I decided to test the other functions, indicators, wipers etc.
Unlike yesterday I got a dead short on ignition :o

I followed Svenedin’s advice and disconnected the brake switch wires before inserting a new fuse and trying again. This time, no short and everything else is working… indicators, wipers, fuel gauge….

I’m not sure why yesterday engaging the brakes caused the short and today it was shorting on ignition, but I’m fairly confident it’s got to be the brake switch. So does this indicate the unit itself has failed or could it still be a wiring issue?
User avatar
svenedin
Minor Legend
Posts: 4973
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Blowing fuses… help!

Post by svenedin »

It does sound like the brake switch. Using your multimeter set to continuity or Ohms, place one multimeter probe on each brake switch terminal. With no pressure on the brake pedal there should be no continuity (open circuit). If the meter beeps for continuity (or shows a low resistance of a few Ohms) then it is stuck in the switch closed position. Possibly the switch failure is also related to the unknown previous owner installed doohickey in the boot.

The switch could also have failed internally with a short to earth (ground). In this case measure continuity between a switch terminal and the switch metal casing. Repeat for the other terminal and the casing.

Is the PO installed thing still connected? Best to get this out of the equation and remove it.

Let us know what you find and if needed we can advise on how to replace the switch.

Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
mrs.smith2012
Minor Addict
Posts: 502
Joined: Wed Sep 17, 2025 6:19 pm
Location: Essex
MMOC Member: Yes

Re: Blowing fuses… help!

Post by mrs.smith2012 »

Thank you, I’ve just tested with the MM and it’s showing an open circuit… so it doesn’t look like the switch is stuck in the closed position. I have attempted to disconnect the weird little plastic thing that is in the boot and obviously wired into the brake lights… but the connector is very tightly wedged into a plastic sleeve… and doesn’t seem to want to come loose so I need to work on a safe way of disconnecting it.
As it’s an obvious ‘weird’ thing I’d like to rule it out before I go messing about with my brake light switch!
User avatar
geoberni
Minor Maniac
Posts: 5337
Joined: Fri Aug 04, 2017 11:19 am
Location: North Leicestershire
MMOC Member: Yes

Re: Blowing fuses… help!

Post by geoberni »

mrs.smith2012 wrote: ↑Thu Nov 19, 2026 11:35 am
The only thing that is really standing out to me right now is this thing… which I’m hoping someone can identify as I have no idea what it is… it appears to be some kind of aftermarket device that somebody has wired in. One wire runs down into the boot… I need to try and trace where it goes… the other appears to be wired into the brake light circuit?? What is this thing?
IMG_9367.jpeg
You've had some good guidance so far on this.
I've not taken part in this discussion so far, as I'm quite busy, but from the look of your photo the item resembles an electronic buzzer... :-?

Back to your earlier photos of the wiring, I'd sum it all up as a bit of a mess, but not dramatically so.
Your car is a 1960.
That lower fuse box is correct for the year.
A Past Owner appears to have converted the car from Pull Start to Solenoid Start for some reason unbeknown to anyone but them.
(Key start was only introduced in 1964. Perhaps they wanted to use the Pull Start position for something else - it's the rightmost switch position of the 4)
Quite silly of them to take a screw out of the clamp for the cable harness to use as a hole for the Red cable.
The upper fusebox is simply a direct feed (Brown/White) from the live side of the Starter Solenoid. As such, it's can't be related to the problem you have at present, if only because it's nothing to do with the fuse which is blowing.
So what you have there is a non-fused permanent live, the one going down and through the screw hole, plus 3 fused outputs, the ones on the right in the photo.
Quite honestly if those are 35A fuses as used in the original fusebox, they might as well not be there because none of that wiring to the right looks capable of taking 35A :o

Additionally, that brown cable to the Starter Solenoid looks a bit thin to take the available output of an Alternator, Perhaps just the original feed from Dynamo to the Control Box that's been rerouted :roll:
It looks as though your alternator connections are via a bit of Chocolate Block tucked in behind the look. :roll:

As it's the lowermost fuse that is blowing I would disconnect and separate all 3 Green wires that are connected to that fuse, then use the Meter to see which is the negligable resistance measurement between wire end and earth.
Connect the other 2 back to the fuse and check the fuse doesn't blow.
The one that is still disconnected is the fault line and likely the brake one.
Basil the 1955 series II

Image
User avatar
svenedin
Minor Legend
Posts: 4973
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Blowing fuses… help!

Post by svenedin »

mrs.smith2012 wrote: ↑Thu Nov 19, 2026 2:06 pm Thank you, I’ve just tested with the MM and it’s showing an open circuit… so it doesn’t look like the switch is stuck in the closed position. I have attempted to disconnect the weird little plastic thing that is in the boot and obviously wired into the brake lights… but the connector is very tightly wedged into a plastic sleeve… and doesn’t seem to want to come loose so I need to work on a safe way of disconnecting it.
As it’s an obvious ‘weird’ thing I’d like to rule it out before I go messing about with my brake light switch!
Show us what this sleeve looks like. It may just be a bullet connector sleeve but best not to pull hard on the unwanted wiring without being sure!

Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
mrs.smith2012
Minor Addict
Posts: 502
Joined: Wed Sep 17, 2025 6:19 pm
Location: Essex
MMOC Member: Yes

Re: Blowing fuses… help!

Post by mrs.smith2012 »

Sorry I did mean to upload a pic
IMG_9368.jpeg
IMG_9368.jpeg (1.72 MiB) Viewed 174 times
Also, I’ve just retested the brake switch terminals and managed to get a bit of a better connection.. now I’m getting a reading of 2.1… so could this indicate the switch has failed? Would explain why I’m now getting a short on ignition without the brake being engaged - although yesterday the brake had to be engaged for the fuse to blow? Testing the individual connectors gives me a reading of about 4-5 although it’s an awkward spot to hold the probe and the readings are jumping around a lot.

Thanks Geoberni for your observations too, I agree it does look like some kind of buzzer but what on earth for and why is it wired into the brake lights? The other grey wire appears to run under the car and disappear back up where the rear seat is? I have no clue!
It bothers me that the previous owner has changed her from a pull start to an ignition start… the pull start knob doesn’t move at all and is not connected to anything else as far as I know. If I could ever have it converted back at any point I will!
mike1864
Minor Fan
Posts: 463
Joined: Tue May 17, 2011 10:06 pm
Location: Hertfordshire
MMOC Member: Yes

Re: Blowing fuses… help!

Post by mike1864 »

Can you clarify whether those ohm readings were taken between the two switch terminals or between each terminal and the switch body?
Remember that if the green/purple wire remains connected, it will present a reading on that terminal of perhaps 4 ohms, being the resistance between the bulbs and the chassis, even if the switch is "good".
Try measuring down that wire with it disconnected.
mrs.smith2012
Minor Addict
Posts: 502
Joined: Wed Sep 17, 2025 6:19 pm
Location: Essex
MMOC Member: Yes

Re: Blowing fuses… help!

Post by mrs.smith2012 »

I took a reading by placing a probe on each of the two terminals on the switch itself (with wires disconnected). The reading was around 2.1.

I then took a reading from each connector by placing the red probe on the connector and the black probe on a bare metal part of the car. Reading was jumping around because it’s an awkward place to hold the probe but averaged between 4-5

If I’ve done this completely wrong please enlighten me! :D
User avatar
svenedin
Minor Legend
Posts: 4973
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Blowing fuses… help!

Post by svenedin »

Just please confirm those reading are Ohms and not thousands or millions of Ohms. So when you say 4 do you mean 4 Ohms?


Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
mrs.smith2012
Minor Addict
Posts: 502
Joined: Wed Sep 17, 2025 6:19 pm
Location: Essex
MMOC Member: Yes

Re: Blowing fuses… help!

Post by mrs.smith2012 »

svenedin wrote: ↑Thu Nov 19, 2026 4:00 pm Just please confirm those reading are Ohms and not thousands or millions of Ohms. So when you say 4 do you mean 4 Ohms?


Stephen
The reading is showing as 02.1 when I place it on the terminals.. and between 04.0-05.0 when testing the connectors :)

I hope that clears it up, sorry I’m not too knowledgeable when it comes to using a multimeter
User avatar
svenedin
Minor Legend
Posts: 4973
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Blowing fuses… help!

Post by svenedin »

mrs.smith2012 wrote: ↑Thu Nov 19, 2026 4:22 pm
svenedin wrote: ↑Thu Nov 19, 2026 4:00 pm Just please confirm those reading are Ohms and not thousands or millions of Ohms. So when you say 4 do you mean 4 Ohms?


Stephen
The reading is showing as 02.1 when I place it on the terminals.. and between 04.0-05.0 when testing the connectors :)

I hope that clears it up, sorry I’m not too knowledgeable when it comes to using a multimeter
It doesn't clear it up unfortunately. Most multimeters have different measurement ranges and a selector knob on the meter. That selector can change the measurement range from Ω to KΩ (1,000s of Ω) to MΩ (millions of Ω). So depending on how the meter is set, 2.1 could mean 2.1 Ω, 21,000 Ω or 2.1 million Ω. If unsure post of picture of the meter as it was set when you took the readings. If set to continuity (beeps when the probes are touched together) then usually the reading is given in Ω.

If it is Ohms then it seems there is a fault with the switch. From your later set of readings, 2.1 Ohms with probes on either brake switch terminal then the switch is closed. Then as I understand it between 4 and 5 Ohms resistance with one probe on switch terminal and another on the metal car body. This is a short to earth due to a faulty switch assuming the wiring was disconnected from the switch when you measured which you confirmed they were.

The previous owner (PO) probably fitted the buzzer so that he knew the brake lights were working. This is because there were (are) a lot of very poor quality brake switches around that fail very quickly. An incredibly annoying thing to have a buzzer sound every time you touch the brake pedal. Barmy! It seems this PO was a bodger who didn't really know what he/she was doing. Your photo appears to show a bullet sleeve. The wires will just pull out of the sleeve but they can be rather tight.

Stephen
Last edited by svenedin on Thu Nov 19, 2026 4:56 pm, edited 1 time in total.
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
mrs.smith2012
Minor Addict
Posts: 502
Joined: Wed Sep 17, 2025 6:19 pm
Location: Essex
MMOC Member: Yes

Re: Blowing fuses… help!

Post by mrs.smith2012 »

IMG_9369.jpeg
IMG_9369.jpeg (1.94 MiB) Viewed 101 times
Does this help? This is what I had my meter set to. Without the probes touching anything it reads as 1. If I touch the probes together I get a reading of 02.1. Same as when I touch each probe to each of the terminals on the switch… 02.1
User avatar
geoberni
Minor Maniac
Posts: 5337
Joined: Fri Aug 04, 2017 11:19 am
Location: North Leicestershire
MMOC Member: Yes

Re: Blowing fuses… help!

Post by geoberni »

That is just a Lucas multi connector, looks like the one where all 4 entry holes are a common connector plate.

As to why they replaced the Pull Start with a remote solenoid..... At current prices, a new manual Pull Switch is around £35, while a remote Solenoid is £10 and a new 3 position key switch is £17. So I doubt cost came into it when you consider the time spend making the changes.
Perhaps they could get used parts, including the solenoid mounting bracket... :-? .
mrs.smith2012 wrote: ↑Thu Nov 19, 2026 3:19 pm I took a reading by placing a probe on each of the two terminals on the switch itself (with wires disconnected). The reading was around 2.1.

I then took a reading from each connector by placing the red probe on the connector and the black probe on a bare metal part of the car. Reading was jumping around because it’s an awkward place to hold the probe but averaged between 4-5

If I’ve done this completely wrong please enlighten me! :D
Depends what the scale was, whether auto ranging or manually set.
Cheaper ones are invariably manually set, e.g. this one I just lifted from the interweb...
Resistance ranges set from 20Megohm down to 200 Ohm...
An auto ranging one will have additional indication on the display to tell you what 'range' it was on.
Multimerter example.JPG
Multimerter example.JPG (38.22 KiB) Viewed 97 times
With the brake pedal not pressed the switch contacts should be open circuit so reading Infinity, or whatever the highest reading of your meter is, in the case of mine that means Flashing at 40 Megohms.
With the pedal pressed, the switch contacts close so should be under 1 Ohm.
Either terminal to the casing should also be reading Infinity.
Basil the 1955 series II

Image
User avatar
svenedin
Minor Legend
Posts: 4973
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Blowing fuses… help!

Post by svenedin »

mrs.smith2012 wrote: ↑Thu Nov 19, 2026 4:55 pm IMG_9369.jpeg

Does this help? This is what I had my meter set to. Without the probes touching anything it reads as 1. If I touch the probes together I get a reading of 02.1. Same as when I touch each probe to each of the terminals on the switch… 02.1
Yes that's helpful as is what you said about touching the probes together.

So the resistance of your probe leads touched together is 2.1Ω and the resistance across the switch is 2.1Ω. This means it's stuck closed inside.

There is more than just a switch failed closed though because you said the resistance is 4 to 5 Ω when measuring between a switch terminal and the car body (wires disconnected). This means the switch is shorting to the casing of the switch. As the casing is metal and that metal is connected to the car body it is shorting to earth. This is why your fuse keeps blowing and why it didn't blow with the green (live) wire disconnected from the switch.

Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
User avatar
svenedin
Minor Legend
Posts: 4973
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Blowing fuses… help!

Post by svenedin »

Now it is established that the brake switch is at fault you will need to replace the switch. The failure of the switch may just be bad luck but I would suggest taking some steps to reduce the likelihood of the switch failing again. One way of doing this which is the simplest way is to fit LED brake light bulbs. These draw much less current so the switch lasts a lot longer. They are also much brighter. I would also suggest removing the extra wiring in the boot.

The switches are not expensive but it can be difficult to change them. You need a deep socket that fits the switch, a really long extension bar and a piece of wood to jam the brake union so that it cannot turn whilst undoing the switch.

Stephen
Last edited by svenedin on Thu Nov 19, 2026 5:13 pm, edited 1 time in total.
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
mrs.smith2012
Minor Addict
Posts: 502
Joined: Wed Sep 17, 2025 6:19 pm
Location: Essex
MMOC Member: Yes

Re: Blowing fuses… help!

Post by mrs.smith2012 »

One thing I notice with my multi meter is that it jumps around a lot. Now it’s a very very good meter.. it belonged to my late father in law who was an electrical engineer.. but it’s incredibly old. I don’t know if they lose accuracy over time.

I have a cheaper basic meter which I will try tomorrow to see if I get different readings… I forgot about that one!

I think I’m just confused because yesterday when I could switch on the ignition and start her and the fuse only blew when I pressed my brake pedal… today it blew immediately without me touching the brakes? What changed? The brake switch would have been connected on both occasions. The only slight difference is that I used a little bit of electrical contact cleaner on the connecting wires before undertaking today’s test.

I should also add, and I apologise for not mentioning it before… but I did recently have a master cylinder replacement. It was done by a professional mechanic, not me fumbling around… but even so, could some wiring have been disturbed? If so where would be the best place to look for possible disturbed wiring, so far I haven’t seen anything untoward expect our plastic friend in the back who I’m still trying to figure out!
mrs.smith2012
Minor Addict
Posts: 502
Joined: Wed Sep 17, 2025 6:19 pm
Location: Essex
MMOC Member: Yes

Re: Blowing fuses… help!

Post by mrs.smith2012 »

svenedin wrote: ↑Thu Nov 19, 2026 5:10 pm Now it is established that the brake switch is at fault you will need to replace the switch. The failure of the switch may just be bad luck but I would suggest taking some steps to reduce the likelihood of the switch failing again. One way of doing this which is the simplest way is to fit LED brake light bulbs. These draw much less current so the switch lasts a lot longer. They are also much brighter. I would also suggest removing the extra wiring in the boot.

Stephen
Thank you, I agree it does look like it’s the switch, but I want to also investigate wiring a little further just to be sure it’s not a wiring fault, particularly with all the questionable wiring in the boot!
User avatar
geoberni
Minor Maniac
Posts: 5337
Joined: Fri Aug 04, 2017 11:19 am
Location: North Leicestershire
MMOC Member: Yes

Re: Blowing fuses… help!

Post by geoberni »

mrs.smith2012 wrote: ↑Thu Nov 19, 2026 4:55 pm IMG_9369.jpeg

Does this help? This is what I had my meter set to. Without the probes touching anything it reads as 1. If I touch the probes together I get a reading of 02.1. Same as when I touch each probe to each of the terminals on the switch… 02.1
If you are reading 'I' with the probes touching nothing at all, then I believe that is your display for 'Infinity' or 'loadsa resistance'.
But if you're getting 2.1 Ohm between the terminals without the pedal pressed then it's stuck in the operated position.
This in itself should just mean the brake lights are on continually so I suspect you'll get the same reading between a terminal and the casing, indicating a short to earth as well. Basically the insides of the switch have all come loose... :roll:
Basil the 1955 series II

Image
User avatar
svenedin
Minor Legend
Posts: 4973
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Blowing fuses… help!

Post by svenedin »

mrs.smith2012 wrote: ↑Thu Nov 19, 2026 5:11 pm One thing I notice with my multi meter is that it jumps around a lot. Now it’s a very very good meter.. it belonged to my late father in law who was an electrical engineer.. but it’s incredibly old. I don’t know if they lose accuracy over time.

I have a cheaper basic meter which I will try tomorrow to see if I get different readings… I forgot about that one!

I think I’m just confused because yesterday when I could switch on the ignition and start her and the fuse only blew when I pressed my brake pedal… today it blew immediately without me touching the brakes? What changed? The brake switch would have been connected on both occasions. The only slight difference is that I used a little bit of electrical contact cleaner on the connecting wires before undertaking today’s test.

I should also add, and I apologise for not mentioning it before… but I did recently have a master cylinder replacement. It was done by a professional mechanic, not me fumbling around… but even so, could some wiring have been disturbed? If so where would be the best place to look for possible disturbed wiring, so far I haven’t seen anything untoward expect our plastic friend in the back who I’m still trying to figure out!
Inside the switch are some electrical contacts. These contacts move slightly and make an electrical circuit with the pressure of the brake fluid when you press the brake pedal. The switches can fail anytime and it was obviously failing yesterday but it stuck shut today. Due to the current drawn by the incandescent brake light bulbs ((about 3.5 amps) there is arcing when the switch closes. Over time this erodes the contacts in the switch and the arcing gets worse. Sometimes this arcing causes the contacts to weld themselves together and then the switch is stuck shut.

I think it is just bad luck and nothing to do with the brake work you had done. That brake work and the brake bleeding afterwards would not have been done with the ignition on so no power to the brake switch.

Stephe
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
mike1864
Minor Fan
Posts: 463
Joined: Tue May 17, 2011 10:06 pm
Location: Hertfordshire
MMOC Member: Yes

Re: Blowing fuses… help!

Post by mike1864 »

Looks like you've found the issue.
Incidentally, what I said earlier about the bulbs' resistance was not accurate. When illuminated they indeed each represent 7 ohms (so 3.5 ohms in parallel). But I just metered (low current of course) a selection of cold bulbs (ie the filament's cool electrons weren't bumping into each other), and they varied around just one ohm.
This is annoyingly close to the dreaded short to chassis we were trying to locate.
Especially if your test leads already have two ohms of resistance. I suspect this is actually a mis-calibration inside the DVM. Or dirty contacts.
Post Reply