Help with fitting LED indicator bulbs

Discuss anything Morris Minor related.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
Post Reply
KevinB
Minor Fan
Posts: 136
Joined: Sun Mar 09, 2025 2:40 pm
Location: Kent
MMOC Member: Yes

Help with fitting LED indicator bulbs

Post by KevinB »

I bought some LED bulbs, but as we know, they don't work with the original flasher unit. They don't flash.

So I have got this new flasher which is supposed to work with LEDs.

New flasher unit
New flasher unit
PXL_20261114_144829179~2.jpg (1.02 MiB) Viewed 1525 times
PXL_20261114_144935727~2.jpg
PXL_20261114_144935727~2.jpg (1001.55 KiB) Viewed 1525 times

Can you please help with how to connect this in? The B, E and L.
I have also asked the seller.

Per the old wiring diagram, I have currently a green power wire, a green/brown to the indicator bulbs and a light green to the switch warning light.

Here's my current flasher unit.
Current flasher unit
Current flasher unit
PXL_20261114_145624342~2.jpg (831.39 KiB) Viewed 1525 times
PS Thanks to who brought back the message board tonight.

PPS I have my Morris back after the welding and brake work, with a fresh MOT.
1967 1098 saloon (known by previous owner as 'Fitzroy')
jaekl
Minor Addict
Posts: 722
Joined: Thu Jun 19, 2008 7:40 pm
Location: Pennsylvania, USA
MMOC Member: No

Re: Help with fitting LED indicator bulbs

Post by jaekl »

Initial thoughts would be B is positive power input and E is negative earth for the flasher itself. Then L is for the lights. I'd suspect that the switch indicator light will need two inputs with diodes on each. The supplier should confirm.
User avatar
svenedin
Minor Legend
Posts: 4946
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by svenedin »

I'm not particularly inspired by the Chingrish on your flasher unit......IF it follows normal convention then

B is battery so that is the plain dark green wire

L is lamps so that is the green with brown trace wire

E is presumably earth so there is no connection for the pilot lamp on the indicator stalk (light green wire)

Conclusion: the unit is not suitable as for the MoT test there must be a tell-tale lamp for the indicators. It is also only suitable for negative earth it appears.

Get one of these which I can personally vouch for. They work perfectly. Note: must be connected to earth which you can do to the mounting bolt. The bracket will need the hole enlarged with a rat's tail file. Purchase the correct polarity unit as they are not interchangeable.

https://www.classiccarleds.co.uk/produc ... -p-2-3-pin

Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
KevinB
Minor Fan
Posts: 136
Joined: Sun Mar 09, 2025 2:40 pm
Location: Kent
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by KevinB »

Thank you jaekl and Stephen.

I was not encouraged by the language on it either! I shall have a play with it and try to understand. Hopefully without doing any damage to the car. And then almost certainly follow your advice Stephen.
1967 1098 saloon (known by previous owner as 'Fitzroy')
moggiethouable
Minor Legend
Posts: 1425
Joined: Tue Jan 17, 2012 12:30 pm
Location: North East England
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by moggiethouable »

" About dodges three times"
Anyone fluent in Chinglish ?
Happiness belongs to the self sufficient
KevinB
Minor Fan
Posts: 136
Joined: Sun Mar 09, 2025 2:40 pm
Location: Kent
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by KevinB »

Quick update:
The chinglish flasher unit is working fine with my new LED bulbs, using the B E L wiring as said above. BUT as Stephen pointed out, there's no feed for the tell-tale interior light.
I don't quite know why this can't come from the L light feed too (?), but that would be clumsy so I will order one of his suggested units.

Thanks all for the help.
1967 1098 saloon (known by previous owner as 'Fitzroy')
User avatar
svenedin
Minor Legend
Posts: 4946
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by svenedin »

KevinB wrote: ↑Sun Nov 15, 2026 3:27 pm Quick update:
The chinglish flasher unit is working fine with my new LED bulbs, using the B E L wiring as said above. BUT as Stephen pointed out, there's no feed for the tell-tale interior light.
I don't quite know why this can't come from the L light feed too (?), but that would be clumsy so I will order one of his suggested units.

Thanks all for the help.
Basically what you have there is a 2 pin flasher that needs an earth connection, not what you need which is a 3 pin flasher. It is actually possible to use a 2 pin flasher AND have the indicator stalk pilot lamp working but it is not straightforward. To make it work you have do some wiring behind the dashboard and use diode leads so that you take the flashed output for the indicator bulbs and feed it to the pilot lamp as well. The diode leads are needed or otherwise you end up with crossover (indicators on both side of the car flashing). It just isn't worth the bother!

If you are NEGATIVE earth you can also use a flasher unit like this (but it does not make a tick tock sound): https://www.autoelectricsupplies.co.uk/ ... asher-unit

This is the better option: https://www.classiccarleds.co.uk/produc ... 95d4&_ss=r

I also have LED indicator bulbs but I am original positive earth. I did not want a modern flasher unit visible on the bulkhead so I sited the modern flasher unit under the dashboard and left the original flasher can on the bulkhead. This has the advantage that the modern LED flasher unit is nearer the driver and clearly audible. These units can also flash incandescent bulbs so you can go back to original bulbs if you want to or in an urgent situation replace a blown bulb with an easily purchased incandescent bulb if you don't happen to have an LED bulb at hand.

Stephen
Last edited by svenedin on Sun Nov 15, 2026 4:47 pm, edited 1 time in total.
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
mike1864
Minor Fan
Posts: 458
Joined: Tue May 17, 2011 10:06 pm
Location: Hertfordshire
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by mike1864 »

And if drawing current off the L terminal is the trigger for making the thing deliver pulsed current, then connecting a pilot bulb (or LED) there would draw just such current. So it would flash all the time? As Stephen says, you need diodes downstream of the indicator switch.
KevinB
Minor Fan
Posts: 136
Joined: Sun Mar 09, 2025 2:40 pm
Location: Kent
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by KevinB »

Thank you both - I'm beginning to understand better.

I'm not going to bother with diodes etc indeed, Stephen! I shall order your better option. I am negative earth and have read your thread about moving the flasher unit.

Hazards are the next project for me, once I've got the normal indicators on LEDs.
1967 1098 saloon (known by previous owner as 'Fitzroy')
User avatar
svenedin
Minor Legend
Posts: 4946
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by svenedin »

KevinB wrote: ↑Sun Nov 15, 2026 4:15 pm Thank you both - I'm beginning to understand better.

I'm not going to bother with diodes etc indeed, Stephen! I shall order your better option. I am negative earth and have read your thread about moving the flasher unit.

Hazards are the next project for me, once I've got the normal indicators on LEDs.
You're welcome. Hazards are really useful. I couldn't be without them now. As I drive my car a lot I have had the misfortunate to break down a few times (same issue all sorted now). Without the hazards these breakdowns could have been rather dangerous.

Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
mike1864
Minor Fan
Posts: 458
Joined: Tue May 17, 2011 10:06 pm
Location: Hertfordshire
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by mike1864 »

In addition to having fitted hazards (vital, as Stephen says), I keep an internally batteried beacon in the car.
Just in case the cause of the breakdown is a flat battery, rather than the (usual!) coil.
My particular model doubles up as a window breaker and seatbelt slasher. And torch!
KevinB
Minor Fan
Posts: 136
Joined: Sun Mar 09, 2025 2:40 pm
Location: Kent
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by KevinB »

Thanks Mike. I have one of those magnetic beacons. (It doesn't do the slashing however!)
And thanks again Stephen.

This board is a rather useful place to be!
1967 1098 saloon (known by previous owner as 'Fitzroy')
Maurice Mynah
Newbie
Posts: 2
Joined: Wed Nov 11, 2026 3:10 pm
Location: UK
MMOC Member: No

Re: Help with fitting LED indicator bulbs

Post by Maurice Mynah »

I don't have hazards. I prefer not to mess around with the existing set up.
I carry a jump pack and a small flashing amber light bar. That fits nicely inside the rear screen plugged into the 12v accessory socket of the jump pack.
User avatar
svenedin
Minor Legend
Posts: 4946
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by svenedin »

Magnetic beacon is of little use with a convertible with no metal roof and I have broken down before with the top down. Hazards can be fitted very neatly without cutting or permanently altering any wiring at all. It does require access to the wiring behind the driver's side glovebox which is a pain to get to requiring taking the steering wheel off etc.

Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
User avatar
geoberni
Minor Maniac
Posts: 5329
Joined: Fri Aug 04, 2017 11:19 am
Location: North Leicestershire
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by geoberni »

Maurice Mynah wrote: ↑Mon Nov 16, 2026 10:42 am I don't have hazards. I prefer not to mess around with the existing set up.
I carry a jump pack and a small flashing amber light bar. That fits nicely inside the rear screen plugged into the 12v accessory socket of the jump pack.
Let's start with a welcome as this is your first post, so.... Welcome.
Is your amber light bar already visible in the rear window along with the Jump pack immediately at your side, or do you have to get them out of the boot.
Because that's on a par with having a fire extinguisher in the boot...not immediately available when you need it :-?
If you brake down on an active Dual Carriageway, you need a Hazard Warning system immediately to hand, not packed neatly in the boot.
There's a good reason aftermarket Hazard Light Units were a popular purchase in the 1970s....
Basil the 1955 series II

Image
Maurice Mynah
Newbie
Posts: 2
Joined: Wed Nov 11, 2026 3:10 pm
Location: UK
MMOC Member: No

Re: Help with fitting LED indicator bulbs

Post by Maurice Mynah »

Both are on the rear seat ready for immediate use.
User avatar
geoberni
Minor Maniac
Posts: 5329
Joined: Fri Aug 04, 2017 11:19 am
Location: North Leicestershire
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by geoberni »

Maurice Mynah wrote: ↑Tue Nov 17, 2026 10:27 am Both are on the rear seat ready for immediate use.
:tu1:
Good to know.
Personally, I have an original 1970s Hazard switch fitted. It's one I removed from a car I was selling in 1977, and had been in my garage ever since, until I brought my Minor :lol:
Basil the 1955 series II

Image
mike1864
Minor Fan
Posts: 458
Joined: Tue May 17, 2011 10:06 pm
Location: Hertfordshire
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by mike1864 »

Maurice Mynah wrote: ↑Tue Nov 17, 2026 10:27 am Both are on the rear seat ready for immediate use.
Immediate? Installed hazard lights can be activated within a second of the engine cutting out, or a perceived incident ahead.
I'd consider a light bar on the back seat (or a beacon in the glove box) as a secondary safety system, only deployable once (and if!) you've reached the hard shoulder/refuge/verge, and left the driver's seat.
Incidentally a magnetic beacon can be used on a convertible:
Beacon.jpg
Beacon.jpg (428.08 KiB) Viewed 222 times
(It also fits on the top of the windscreen)
User avatar
Bill_qaz
Minor Legend
Posts: 2391
Joined: Fri Jan 14, 2022 7:31 pm
Location: Oxfordshire
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by Bill_qaz »

Too late for a beacon Mike you have rolled it :lol:
Flipped it back on its wheels for you :tu1:
Beacon.jpg
Beacon.jpg (330.63 KiB) Viewed 159 times
Regards Bill
User avatar
svenedin
Minor Legend
Posts: 4946
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Help with fitting LED indicator bulbs

Post by svenedin »

mike1864 wrote: ↑Tue Nov 17, 2026 12:13 pm
Maurice Mynah wrote: ↑Tue Nov 17, 2026 10:27 am Both are on the rear seat ready for immediate use.
Immediate? Installed hazard lights can be activated within a second of the engine cutting out, or a perceived incident ahead.
I'd consider a light bar on the back seat (or a beacon in the glove box) as a secondary safety system, only deployable once (and if!) you've reached the hard shoulder/refuge/verge, and left the driver's seat.
Incidentally a magnetic beacon can be used on a convertible:Beacon.jpg
(It also fits on the top of the windscreen)
I don't think I had appreciated hazards on the older Minors. It is all very well to have hazards on my late Minor with large amber indicators but for older cars with brake lights for indicators or only semaphores then I can see why a beacon is a better idea.

Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
Post Reply