Engine identification please.

Discuss anything Morris Minor related.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
mike1864
Minor Fan
Posts: 448
Joined: Tue May 17, 2011 10:06 pm
Location: Hertfordshire
MMOC Member: Yes

Re: Engine identification please.

Post by mike1864 »

IIRC, on mine I just fitted the later cover. The rear end of the tunnel wasn't affected.
The engine floor needed a bit of a trim to accommodate the cylinder oil filter (versus the original - and arguably better/easier - spin-on).
Splitty-Moggy
Newbie
Posts: 8
Joined: Fri Oct 02, 2026 10:09 am
Location: Sussex
MMOC Member: Yes

Re: Engine identification please.

Post by Splitty-Moggy »

I just took a couple of pictures yesterday don’t know if you can tell from that?
Attachments
IMG_6754.jpeg
IMG_6754.jpeg (3.62 MiB) Viewed 444 times
IMG_6753.jpeg
IMG_6753.jpeg (3.25 MiB) Viewed 444 times
User avatar
geoberni
Minor Maniac
Posts: 5352
Joined: Fri Aug 04, 2017 11:19 am
Location: North Leicestershire
MMOC Member: Yes

Re: Engine identification please.

Post by geoberni »

I assume we're going through these questions because the paperwork still says 803.
That's either a 948 or 1098 gearbox but you'll need to look at the outside to see if it's the smooth or ribbed (stronger) case of the 1098.
Just shine a torch down past the exhaust and you'll be able to see which.

Just because we have settled on the engine being 1098 doesn't guarantee whomever did that got the right gearbox.
A PO of my car fitted a 1098 when they thought they were fitting a 948.... :roll:
Basil the 1955 series II

Image
myoldjalopy
Minor Legend
Posts: 3568
Joined: Tue Jan 29, 2013 10:32 pm
Location: Kernow
MMOC Member: Yes

Re: Engine identification please.

Post by myoldjalopy »

What we can tell is that the floor has been chopped to fit the later gearbox tunnel to accommodate the later remote change mechanism. Fairly typical conversion and often seen in these SII cars. The later handbrake lever has also been fitted, although they retained the 803 gearknob on the later gear lever. Pic shown previously suggests that it is a 1098 box.
mike1864
Minor Fan
Posts: 448
Joined: Tue May 17, 2011 10:06 pm
Location: Hertfordshire
MMOC Member: Yes

Re: Engine identification please.

Post by mike1864 »

myoldjalopy wrote: ↑Mon Oct 05, 2026 9:48 am What we can tell is that the floor has been chopped to fit the later gearbox tunnel to accommodate the later remote change mechanism. Fairly typical conversion and often seen in these SII cars. The later handbrake lever has also been fitted, although they retained the 803 gearknob on the later gear lever. Pic shown previously suggests that it is a 1098 box.
I had to fit the later type handbrake lever as the front of the (longer) SII lever fouled the relocated gear lever. One of those things you don't realise till towards the end of the job!
Splitty-Moggy
Newbie
Posts: 8
Joined: Fri Oct 02, 2026 10:09 am
Location: Sussex
MMOC Member: Yes

Re: Engine identification please.

Post by Splitty-Moggy »

Thanks all for the information. Been so busy haven’t had a chance to do anything to it yet. Just another quick one I’m going to strip, clean and rebuild the carb. It’s the HS2 carb i have in mine right? Thank you again for all the information, appreciated it. Henry.
Attachments
IMG_6742.jpeg
IMG_6742.jpeg (3.58 MiB) Viewed 132 times
IMG_6744.jpeg
IMG_6744.jpeg (3.57 MiB) Viewed 132 times
IMG_6746.jpeg
IMG_6746.jpeg (1.8 MiB) Viewed 132 times
IMG_6747.jpeg
IMG_6747.jpeg (3.26 MiB) Viewed 132 times
Post Reply