Page 1 of 1

Clutch part

Posted: Sat Oct 28, 2023 7:09 pm
by Classiccars
Can you please advise if this could be a genuine morris part as the engine is 1275 and gearbox sierra .
20231028_123711.jpg
20231028_123711.jpg (1.56 MiB) Viewed 4152 times
20231028_123241.jpg
20231028_123241.jpg (1.46 MiB) Viewed 4152 times
20231028_122903.jpg
20231028_122903.jpg (1.63 MiB) Viewed 4152 times
20231028_123002.jpg
20231028_123002.jpg (1.33 MiB) Viewed 4152 times

Re: Clutch part

Posted: Sat Oct 28, 2023 9:09 pm
by Classiccars
Just yo add I need to change as leaking.

Re: Clutch part

Posted: Sat Oct 28, 2023 9:33 pm
by simmitc
The Minor had a purely mechanical clutch linkage, so the slave cylinder is not a Minor part. Different cylinders can be used. Hopefully someone will recognise the part number and tell you what your one is from.

Re: Clutch part

Posted: Sat Oct 28, 2023 10:26 pm
by les
I think this photo has been shown before, I remember seeing two different bolts securing it, I wonder what the thinking was behind doing that. Perhaps the cylinder is from a Mini.

Re: Clutch part

Posted: Sat Oct 28, 2023 11:53 pm
by philthehill
The clutch slave cylinder is not Morris but is BMC.
The clutch slave cylinder is a 948c/1098cc MG Midget/Sprite item Pt No: GSY110 (MOSS).
https://www.ebay.co.uk/itm/173952850905 ... R_jou4fvYg
This type of slave cylinder was fitted to the 948cc, 1098cc & 1275cc MG Midget/Sprite and all variants of FWD BMC/BL vehicles.
The classic Mini (pre Verto) and the MG Midget/Sprite are virtually the same and either can be used for a 1275cc Midget application though the correct slave cylinder for a 1275cc clutch is Pt No GSY113 (MOSS).
I would replace the cylinder complete and not bother trying to repair.
These are the two bolts that should be used for securing the clutch slave cylinder
https://www.ebay.co.uk/itm/393990653042 ... R8CnnonvYg

Re: Clutch part

Posted: Sun Oct 29, 2023 9:03 am
by Classiccars
Thanks very much.I will order one.Can I finally ask please.Does the rod secure onside the piston as it has it is like a very long screw. Also when I had the clutch working the rod was movable side to side as if not tight in the piston.But when screwed up it was tight and not moveable.Also why the new bolts please as I will order if you think so.

Re: Clutch part

Posted: Sun Oct 29, 2023 9:38 am
by philthehill
The rod just sits inside the cup of the slave cylinder piston. It is not attached to the piston in any way.
The correct clearance allows the rod to move sideways.
This is the rod that should be fitted:-
https://www.ebay.co.uk/itm/351002920998 ... R6iY86zvYg
You have one or more incorrect bolts holding the slave cylinder to the bell housing. For completeness and correctness I would replace the bolts with the right items. Also how do you know if the bolts are the correct length?
Below is the clutch hydraulic slave cylinder fitted to my Minor.
I have made the release rod adjustable in length.
Hydraulic clutch 6.JPG
Hydraulic clutch 6.JPG (855.79 KiB) Viewed 4093 times

Re: Clutch part

Posted: Sun Oct 29, 2023 11:35 am
by Classiccars
Thanks very much I can move forward now.Much appreciated.

Re: Clutch part

Posted: Sun Oct 29, 2023 12:45 pm
by les
It’s possible that the odd bolts are a consequence of a striped thread in the housing, necessitating an oversize bolt when re threaded.
However I think I’d have to make both threads the same, at least get the heads the same type. I couldn’t look at that mismatch every-time I lifted the bonnet but then that’s just me ! :D

Re: Clutch part

Posted: Sun Oct 29, 2023 8:47 pm
by Classiccars
Thanks Les