Page 1 of 1
name that part (part two)
Posted: Thu Apr 28, 2011 2:52 pm
by xpress
here we go again ladies, a few parts, let's see if you can all name them and any comments please.
here we go ...[frame]
[/frame][frame]
[/frame][frame]
[/frame][frame]
[/frame][frame]
[/frame][frame]
[/frame]
Re: name that part (part two)
Posted: Thu Apr 28, 2011 3:24 pm
by Stig
xpress wrote:here we go again ladies, a few parts, let's see if you can all name them
Erm, gearstick, diff, clutch, pushrods, dynamo bracket, clutch rod, flywheel. Do I win a prize?
xpress wrote:and any comments please.
Yeah, the flywheel's rusty.
Re: name that part (part two)
Posted: Thu Apr 28, 2011 3:27 pm
by xpress
ooo, you're good you are ..!
Re: name that part (part two)
Posted: Thu Apr 28, 2011 3:48 pm
by rayofleamington
and a clutch cover, a nut, a dynamo adjuster shaft, and maybe a draught excluder?
Re: name that part (part two)
Posted: Thu Apr 28, 2011 4:22 pm
by Alex'n'Ane
Cardboard!
Now do you take the picture away and we have to try and remember...
Re: name that part (part two)
Posted: Thu Apr 28, 2011 4:57 pm
by Neil MG
"battery clamp, cuddly toy, toaster, decanter, tv...did I say cuddly toy....
Oooh! Didn't he do well..."
Re: name that part (part two)
Posted: Thu Apr 28, 2011 6:54 pm
by chrisryder
cover and plate look like 1098 clutch to me.
diff could be anything, you should see some numbers stamped on the outside edge of the large gear. expect to see 9/38 for a 4.22 diff, or something similar for other diff ratios. you never know you could have a valuable one!
i'd be tempted to say the roll of stuff is wing piping rather than draught excluder, but it's hard to tell.
Re: name that part (part two)
Posted: Thu Apr 28, 2011 7:02 pm
by Alex'n'Ane
i'd guess boot bonnet rubber seal.
Re: name that part (part two)
Posted: Thu Apr 28, 2011 8:16 pm
by irmscher
they are defintely thingymajigs and watchucallits do i get a prize
Re: name that part (part two)
Posted: Thu Apr 28, 2011 8:31 pm
by Alex'n'Ane
And they all need to be fitted with a hammer..
Re: name that part (part two)
Posted: Thu Apr 28, 2011 8:56 pm
by LouiseM
chrisryder wrote:i'd be tempted to say the roll of stuff is wing piping rather than draught excluder, but it's hard to tell.
Looks like it might be a boot seal
xpress - are you asking because you don't know what the parts are? (If so a workshop manual will help
)
Re: name that part (part two)
Posted: Thu Apr 28, 2011 9:05 pm
by chrisryder
ok, it could be a bootseal! i've been looking at various computers all day. my eyesight isn't what it used to be
i like these light-hearted competitions. we have a thing like this at a car club christmas meal each year. the organiser brings a bit of car and it gets passed around and we have to work out what car it's from!
Re: name that part (part two)
Posted: Thu Apr 28, 2011 10:25 pm
by les
I should have seen part 1, maybe that wouldn't have been so difficult!
Re: name that part (part two)
Posted: Thu Apr 28, 2011 10:46 pm
by LouiseM
Here's part 1 Les. See how you get on:
http://www.mmoc.org.uk/viewtopic.php?f=1&t=37620
It's not getting more difficult - the parts are just getting rustier
Re: name that part (part two)
Posted: Thu Apr 28, 2011 11:05 pm
by irmscher
is the rubber a roof seal for a traveller