I have just taken my car out for a short drive and found this 3/4 inch long screw on the drive just behind where my car usually sits. It looks familiar but I can't think where I have seen it before, is it to set the beam on the headlights?
any ideas anybody?[frame][/frame]
Can anybody identify this screw?
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
Can anybody identify this screw?
Last edited by pjh56 on Sat Mar 05, 2011 9:58 am, edited 1 time in total.
My 1970 2 door saloon Trafalgar Blue
-
- Moderator
- Posts: 7592
- Joined: Thu Feb 14, 2002 12:00 am
- Location: Watford, Hertfordshire.
- MMOC Member: No
Re: Can anybody identify this screw?
Rusty screws always look familiar to me, what diameter is it.
Cheers
Kevin
Lovejoy 1968 Smoke Grey Traveller (gone to a new home after13 years)
Herts Branch Member
Moderator MMOC 44706
Kevin
Lovejoy 1968 Smoke Grey Traveller (gone to a new home after13 years)
Herts Branch Member
Moderator MMOC 44706
-
- Minor Legend
- Posts: 2217
- Joined: Mon Nov 15, 2010 11:44 pm
- Location: West Midlands UK
- MMOC Member: No
Re: Can anybody identify this screw?
if it's quite small (2BA or M5-ish) then it could be a hockey stick stud and nut. mine were forever popping out. studs are now loctited in
-
- Minor Maniac
- Posts: 7845
- Joined: Thu Jan 25, 2007 3:18 pm
- Location: South East London
- MMOC Member: No
Re: Can anybody identify this screw?
I'm pretty sure hockey stick studs aren't pointed.
Someone's chucked it under your car to wind you up.
Someone's chucked it under your car to wind you up.
"Once you break something you will see how it was put together"
Re: Can anybody identify this screw?
At the non-pointed end, has it sheared off? If yes, then there could be a head missing, if no, then it's a stud.
If it is sheared, is the break as rusty as the rest? If yes then it's been there a long time.
Is the apparent rim to the left of the nut genuinely an un-threaded collar? If yes, then it again points to a stud.
Depending on the diameter, seat fixing bolts and door hinge bolts usually have pointed ends. However, the hinge would not normally have a nut (it goes into a plate). If it's from the seat mounting then it means that the nut separated from the floor. so get out the welding kit.
Of course, a previous owner could have used any bolr to secure any thing.
If it is sheared, is the break as rusty as the rest? If yes then it's been there a long time.
Is the apparent rim to the left of the nut genuinely an un-threaded collar? If yes, then it again points to a stud.
Depending on the diameter, seat fixing bolts and door hinge bolts usually have pointed ends. However, the hinge would not normally have a nut (it goes into a plate). If it's from the seat mounting then it means that the nut separated from the floor. so get out the welding kit.
Of course, a previous owner could have used any bolr to secure any thing.
Re: Can anybody identify this screw?
I think it is off the hockey stick because I remember seeing it when I replaced them last year.
Thank you for your help
Regards
Peter
Thank you for your help
Regards
Peter
My 1970 2 door saloon Trafalgar Blue
-
- Series MM Registrar
- Posts: 10183
- Joined: Sun Jul 24, 2005 11:39 pm
- Location: Reading
- MMOC Member: No
Re: Can anybody identify this screw?
Chuck it in your tin of spare bolts until you find what it fits. It will probably still be there in ten years time - unless you throw it away when you will be looking for it next week.
[sig]3580[/sig]
Re: Can anybody identify this screw?
mike.perry wrote:Chuck it in your tin of spare bolts until you find what it fits. It will probably still be there in ten years time - unless you throw it away when you will be looking for it next week.
My 1970 2 door saloon Trafalgar Blue