Datums and dimensions
Posted: Mon Apr 19, 2004 4:13 am
Does anybody have or know of chassis dimensions and datums suitable for staightening a minor that has been in an accident.
(the thick ring binder one).Morris Minor Owners Club
Promoting the Preservation and Use of the Postwar Morris Minor
https://board.mmoc.org.uk/
Datums and dimensions
Page 1 of 1
Posted: Mon Apr 19, 2004 5:51 am
The factory manual has a very good section specifically for this (the thick ring binder one).
(the thick ring binder one).Posted: Mon Apr 19, 2004 8:25 am
Hello Sii83,
the Haynes manual also gives some limited datum dimensions.:-
Front and rear of torsion bar 22 7\8" 58.1 cm from left to right.
Ends of front spring hanger bolt 42 23\64" 107.59 cm from left to right.
Ends of rear spring hanger bolts 42 7\8" 108.9 cm.
Across front bumper mounting legs 34 1\8"
Alec
the Haynes manual also gives some limited datum dimensions.:-
Front and rear of torsion bar 22 7\8" 58.1 cm from left to right.
Ends of front spring hanger bolt 42 23\64" 107.59 cm from left to right.
Ends of rear spring hanger bolts 42 7\8" 108.9 cm.
Across front bumper mounting legs 34 1\8"
Alec
Posted: Tue Apr 20, 2004 4:09 am
Scott, Alec,
Thanks for you replies. Scott, do you know which edition of the manual you have and its title? I have a very old factory manual which covers the seires MM and series II, the section on the body is very limited.
Alec, I guess that the dimmension for the front torsion bar you gave me was from centerline to centerline?
Cheers,
Matt
Thanks for you replies. Scott, do you know which edition of the manual you have and its title? I have a very old factory manual which covers the seires MM and series II, the section on the body is very limited.
Alec, I guess that the dimmension for the front torsion bar you gave me was from centerline to centerline?
Cheers,
Matt
Posted: Tue Apr 20, 2004 11:56 am
Hello Matt,
yes, that's correct.
Alec
yes, that's correct.
Alec
Posted: Thu Apr 22, 2004 4:11 am
sii803
You're a local !!!! - well as local to me as it gets on here .
The manula I use is the genuine BMC one. It has a part # of AKD530. Other ones I have have a # of AKD530D & AKO530K.
If you like, I can send/fax you the pages to you (fax easier - PM me if you have access to one).
The manuals are around; have you checked with your club in Adelaide?
You're a local !!!! - well as local to me as it gets on here
.The manula I use is the genuine BMC one. It has a part # of AKD530. Other ones I have have a # of AKD530D & AKO530K.
If you like, I can send/fax you the pages to you (fax easier - PM me if you have access to one).
The manuals are around; have you checked with your club in Adelaide?
Posted: Fri Apr 30, 2004 10:49 pm
If you have difficulty getting a Workshop Manual there's a seller on ebay sells a CD of the full manual in pdf format. He's on quite regularly. I bought one and it's extremely useful as a reference file whilst at the pc. You can also print out the page(s) you want and not worry about getting greasy fingers all over it/them. Don't know about the copyright situation, though. I've just looked at mine and the pages you want are R16 and R17. This shows a MM but I think the principal dimensions are correct for all saloon models. Maybe others will advise you on this.
Nick
Nick
Posted: Mon May 03, 2004 4:14 am
Thanks everyone for your help. It seems that my manual is missing pages R16 and R17. I have however found the dimensions from the dep dark depths of the State Library of South Australia. They had some ineteresting publications from the fifties and sixties, which they happily retrieved from storage for me. Some of them are "technical papers" published in australia for the benifit of mechanis I guess.
If this information is out of copyright, it would be great to have it posted on this site.
Thanks again for everyones help
Matt
If this information is out of copyright, it would be great to have it posted on this site.
Thanks again for everyones help
Matt