Page 1 of 1
Morris 2 litre Twin Cam Dyno Results
Posted: Thu Nov 11, 2010 1:16 pm
by Wal
Dear all,
finally got my Morris properly tuned this year by a decent rolling road and engineer. Just thought I'd share the results, it was done back in the summer and I've been enjoying it too much to post before.
Peak power is 167.6 BHP at 7,500 rpm. Peak torque is 142.7 lb/ft at 5000 rpm. More important to me is it reaches 120 lb/ft torque at 3,750 rpm and stays above that till practically 7,250 rpm giving a lovely long flat torque curve.
Power is not quite as good as it should be because of my exhaust set up, but I like it as it is and don't want to change it.
Regards,
Wal
[frame]
[/frame]
Re: Morris 2 litre Twin Cam Dyno Results
Posted: Thu Nov 11, 2010 9:43 pm
by heathy12
Heres mine, 1380cc A series force fed!
Re: Morris 2 litre Twin Cam Dyno Results
Posted: Thu Nov 11, 2010 11:04 pm
by Wal
That's nice Heathy12, good steep curve. Take off must be great fun.
The drop off looks a bit harsh though.
Like the force fed, got the supercharger version for mine. Just trying to find the time.....
Regards,
wal
Re: Morris 2 litre Twin Cam Dyno Results
Posted: Mon Nov 22, 2010 9:51 am
by polo2k
can we see pics of the cars and their engines
Re: Morris 2 litre Twin Cam Dyno Results
Posted: Fri Dec 17, 2010 1:38 pm
by Faceplant
very interesting!
can i ask is it a standard twin cam? twin carbs etc?
I have been meaning to get mine tuned but didnt get round to it. who did yours?
FP
Re: Morris 2 litre Twin Cam Dyno Results
Posted: Fri Jan 21, 2011 2:23 pm
by Wal
Faceplant,
it's a full Guy Croft engine, information below. It is expensive but you get what you pay for and the engine delivers the results. I wouldn't bother taking my twin cam to anyone else.
Regards,
Wal
Guy Croft Head No. 02.021.1
Head: 130 Abarth 8v head
Valves: 43.5mm inlet; 36mm exhaust
Cams: GC 3A inlet and exhaust
Pulleys: GC vernier type
Valve springs: triple
Head work: Guy Croft
Plugs: NGK B9EGV
Fueling
Carbs: 2 * Weber 45 DCOE using 38 chokes, F16 emulsion tubes, 145 main jet and 175 air corrector
Pump: Facet red top
Guy Croft Block No. 03.043.1
Block: 2 litre Fiat 131
Pistons: GC Forged Race
Rods: GC Race
Exhaust
Custom built 50mm stainless 4-2-2 system with Magnaflow main box and Scorpion back box
Others
Lightened flywheel by GC
Uprated clutch and plate
Moroso Accusump
13 row oil cooler
Modified FIAT 131 sump
1” Cam belt
GC Head bolts
Re: Morris 2 litre Twin Cam Dyno Results
Posted: Tue Feb 22, 2011 6:50 pm
by Faceplant
I have a guy croft head also, he did a full rebuild and its setup with twin dellorto 40's, and custom 2' stainless exhaust. though the bottom end is standard and the previous owner did the final tune. it goes well, lots of low end torque and a fabulos rasp when the clutch is engaged to change gear! puts a smile on my face every time
Carb setup:
34 chokes
162 mains
62 idles
7772.11
210 airs
38 pumps
I'm going to get it tuned in a couple of months - just completed a jlh dampner kit front and rear whic cost a few quid!
i spoke to a tuner in essex, sounded like he knew what he was doing and was around £100, unfortunately Guy Croft is too far away!