Just for fun
Posted: Mon Jun 15, 2009 10:12 am
Would you be able to identify each part from left to right?
Hint they are all series II parts
Hint they are all series II parts
Morris Minor Owners Club
Promoting the Preservation and Use of the Postwar Morris Minor
https://board.mmoc.org.uk/
Just for fun
Page 1 of 1
Posted: Mon Jun 15, 2009 10:22 am
I can't see the image.......
Posted: Mon Jun 15, 2009 12:05 pm
Thanks now sorted
Posted: Mon Jun 15, 2009 5:02 pm
OK, from left to right…
Bonnet Slam Plate
Rear seat hinge
Wire Loom Anchor
Steering Wheel Mount
?? Mount for main-beam switch
Bonnet Release cam-arm
Bonnet Stay
?? Don’t know but will probably kick myself.
Other rear seat hinge
Bonnet catch
Hand brake
The two shiny bits are the connectors for the bonnet release mech
How did I do????
Bonnet Slam Plate
Rear seat hinge
Wire Loom Anchor
Steering Wheel Mount
?? Mount for main-beam switch
Bonnet Release cam-arm
Bonnet Stay
?? Don’t know but will probably kick myself.
Other rear seat hinge
Bonnet catch
Hand brake
The two shiny bits are the connectors for the bonnet release mech
How did I do????
Posted: Mon Jun 15, 2009 6:23 pm
Dont know what most of them are but they make a rubbish shower curtain.
Posted: Mon Jun 15, 2009 6:25 pm
I thought this was one of those special gadgets you see hanging in old kitchens - add a few pots and pans and would make a nice focal point. I'm sure it would inspire all sorts of conversations whilst around the dinner table 
Posted: Mon Jun 15, 2009 7:45 pm
Mary asks
Is it a torture chamber?
Or is it for some other usage?
Is it a torture chamber?
Or is it for some other usage?
Posted: Mon Jun 15, 2009 8:00 pm
I like the shower curtain idea, but they would need a decent coat of paint to stop them rusting....
I can see it being the focal on 'Grand Designs'.....
I can see it being the focal on 'Grand Designs'.....
Posted: Tue Jun 16, 2009 8:28 am
Wire loom anchor
Mount for main-beam switch
Don’t know but will probably kick myself
The two shiny bits are the connectors for the bonnet release mech
these are incorrect, apart from the shiny bits which are the pins for the bonnet stay, these are parts only seen on mm's and series II
Torture chamber.... ... the only torture here is that I long to see everything fixed to the car and up and running!
Mount for main-beam switch
Don’t know but will probably kick myself
The two shiny bits are the connectors for the bonnet release mech
these are incorrect, apart from the shiny bits which are the pins for the bonnet stay, these are parts only seen on mm's and series II
Torture chamber....
... the only torture here is that I long to see everything fixed to the car and up and running!Posted: Tue Jun 16, 2009 10:43 am
Keep dreaming Mark - you'll get there in the end!
Posted: Wed Jun 17, 2009 7:32 am
Hints
One little bit is found in the boot space...
Another bit with two bolts has something to do with a light...
The odd bit is somewhere near a carburettor
One little bit is found in the boot space...
Another bit with two bolts has something to do with a light...
The odd bit is somewhere near a carburettor
Posted: Wed Jun 17, 2009 10:37 am
so that'll make them....
Boot stay hold up clip
Rear light base
Throttle return spring bracket
???
Boot stay hold up clip
Rear light base
Throttle return spring bracket
???
Posted: Wed Jun 17, 2009 11:52 am
only one wrong now....the last one should read : steady bracket for old type air filter, fits to tube air filter and manifold duct and shows slightly in this pic:
http://potteries.mmoc.org.uk/RallyPics/ ... re_106.jpg
http://potteries.mmoc.org.uk/RallyPics/ ... re_106.jpg
