Page 1 of 1
Carb identification
Posted: Sat Jun 23, 2007 5:58 pm
by youngun
Went along to an auction today, missed out on a 1098 engine that went for a tenner
. Anyway, I picked up an HS2 on its manifold and another SU carb as well, both for a quid, not bad me thought. But, can anyone identify what this carb is, and will it be any good as some kind of moggy mod? The dashpot is a LOT bigger than that of your normal moggy carb, and the butterfly has "22.5" stamped on it.
http://i166.photobucket.com/albums/u118 ... n07001.jpg
http://i166.photobucket.com/albums/u118 ... n07005.jpg
http://i166.photobucket.com/albums/u118 ... n07003.jpg
Thanks,
YG
Posted: Sat Jun 23, 2007 6:48 pm
by Alec
Hello YG,
it looks very much like an HS4, easily checked by measuring the bore.
S.U.'s are numbered by the bore or choke diameter, 1" + the number of 1\8"s, therefore a HS4 or a H4 is a 1" + 4 x 1\8" =11\2".
You will need a different manifold as the bolt configuration is different but it is OK for a 1098 especially if you find a better head.
Alec
Posted: Sat Jun 23, 2007 8:06 pm
by youngun
Thanks alec, ill get my Verniers out tommorrow.
My engine is a 948, would the carb still be any good, or would i have to fit a different head?
Posted: Sat Jun 23, 2007 8:15 pm
by Alec
Hello YG,
probably not as useful unless you do a lot of work on it, I had assumed a 1098, sorry.
Alec
Posted: Sat Jun 23, 2007 9:26 pm
by bmcecosse
Oh the 948 will be fine with a bigger carb - but a bigger valve head will be even better! Thought you were fitting a 940 head ?
Posted: Sat Jun 23, 2007 9:54 pm
by youngun
bmcecosse wrote:Oh the 948 will be fine with a bigger carb - but a bigger valve head will be even better! Thought you were fitting a 940 head ?
Aye i will be, engine is coming out tommorrow.....like i say BM, ill be in touch!
Posted: Sun Jun 24, 2007 2:34 pm
by Packedup
Yep, HS4, and should be OK for a 948 I'd have thought. The 998 Minis had HS2 carbs to start with but went to HS4 (around mid 73 IIRC) and never had a problem, can't see why that 50cc less should be hurt with 1/4" more carb
It will, as posted, need a different inlet to use it though.
It would also benefit from a solid butterfly instead of that nasty poppet vlaved one, but at least it's not a waxstat jet!
Posted: Sun Jun 24, 2007 2:36 pm
by Packedup
Although looking again, is it the rear carb off a Triumph install? I'm thinking teh float and linkages are the wrong way round for a single carb setup...
Posted: Sun Jun 24, 2007 8:23 pm
by youngun
Would the air filter be a giveaway, if so ill put a picture up of it.
Posted: Sun Jun 24, 2007 8:25 pm
by youngun
Posted: Sun Jun 24, 2007 9:07 pm
by Packedup
youngun wrote:Would the air filter be a giveaway, if so ill put a picture up of it.
The air filter should help point towards what it came off.
I'm trying to work out if it's a normal single or the rear of twins, and can't quite get to the cupboard I can see the end of a twin inlet with carbs in to check!
Whereabout was this auction? Someone mentioned one on the Dorset/ Devon border the other week where there were bargains to be had, seems I only hear about them after the event!
Posted: Sun Jun 24, 2007 10:01 pm
by youngun
The auction was in Holsworthy, North Devon.
Ill take a snap of the air filter, and the underside fo the carb.
YG
Posted: Mon Jun 25, 2007 6:47 pm
by bmcecosse
Whatever carb it is - it will work ok on the Minor provided it fits the manifold.
