Page 4 of 4
Re: Ford discs-sticking caliper?
Posted: Tue May 18, 2021 5:54 pm
by ndevans
Bowie69 wrote: ↑Tue May 18, 2021 5:45 pm
ndevans wrote: ↑Tue May 18, 2021 4:04 pm
Only problem with using the old carrier as a drift is..... How do I then remove it when it becomes stuck in the hub along with the new one?
You either grind down the circumference, or cut a slot in it before doing so....
Bit late now!
Re: Ford discs-sticking caliper?
Posted: Tue May 18, 2021 9:16 pm
by ndevans
A bit of heat, and some wiggling of the old carrier with a small pair of molegrips released it.
Re: Ford discs-sticking caliper?
Posted: Wed May 19, 2021 9:37 am
by ndevans
I have measured the outer diameter of the carrier with a Vernier caliper. it comes out as 47.04mm. The inside diameter of where it fits in the hub, however, is as best as I can make out, 46.82mm. so over 0.2mm interference. Without wishing to put ideas into anyone's head-that seems a bit too much of a difference to me?
Re: Ford discs-sticking caliper?
Posted: Wed May 19, 2021 10:33 am
by oliver90owner
It is not a carrier; it is one of the bearing races. IF the difference is 0.2mm interference fit, that is in the realms of permanent shrink fitting. I suggest the ‘best you can make out’ is simply not good enough.
You have the old race and the new one, so compare them? If the bearing race went in and the old one came out relatively easily, what are you messing about at?
Use a micrometer (not a caliper), btw, for accurate measurements. Do you have internal point calipers for comparative measurement (by the same measuring instrument)?
Re: Ford discs-sticking caliper?
Posted: Wed May 19, 2021 10:45 am
by ndevans
oliver90owner wrote: ↑Wed May 19, 2021 10:33 am
It is not a carrier; it is one of the bearing
races. IF the difference is 0.2mm interference fit, that is in the realms of permanent shrink fitting. I suggest the ‘best you can make out’ is simply not good enough.
You have the old race and the new one, so compare them? If the bearing race went in and the old one came out relatively easily, what are you messing about at?
Use a micrometer (not a caliper), btw, for accurate measurements. Do you have internal point calipers for comparative measurement (by the same measuring instrument)?
I have a set of internal calipers, but I don't have a micrometer larger enough to do 47mm-mine is a 25mm. I've only tried measuring the internal diameter using the vernier caliper, I can't lay my hands on the internal caliper currently.
The old race is the same as the new, 47.04mm.
Re: Ford discs-sticking caliper?
Posted: Wed May 19, 2021 2:28 pm
by oliver90owner
Not measuring it properly is just as good as not measuring it at all.
Re: Ford discs-sticking caliper?
Posted: Mon Jul 19, 2021 9:46 pm
by ndevans
So I *think* I've cracked the problem of the "mystery rhythmic knocking". Having got the engine out, I thought I'd have a look at the gearbox, a quick visual inspection to see of anything obviously won't with the rear bearing. Well, there was no sign of it slipping or turning within the carrier or the bell housing, a long shot, but I thought I'd check.
However, there was this:-
https://youtube.com/shorts/FK4sSC7SRbc?feature=share
All tightened up now. The engine isn't ready to go back in yet, but it looks like a smoking gun to me. Proof of the pudding will be in the eating.
Cheers N