Blowing fuses… help!

Discuss anything Morris Minor related.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
User avatar
geoberni
Minor Maniac
Posts: 5337
Joined: Fri Aug 04, 2017 11:19 am
Location: North Leicestershire
MMOC Member: Yes

Re: Blowing fuses… help!

Post by geoberni »

I concur with Stephen.

There's a good article written in 2007 about hydraulically operated Brake Light Switches, specifically those fitted to classic Volvo models.
Being an American article it does have some amusing DIY solutions to installing alternative switches, something they could/can get away with since few US States have any form of vehicle inspection regime. :o

https://www.sw-em.com/hydraulic%20brake ... 0notes.htm

Interestingly, a 2016 article in Minor Matters, which is reproduced on the Dorset Branch website uses the same illustrations..... :wink:
https://dorsetmmoc.co.uk/website_7023d1 ... chfail.pdf
Basil the 1955 series II

Image
User avatar
svenedin
Minor Legend
Posts: 4973
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Blowing fuses… help!

Post by svenedin »

Good Minor Matters article but what it doesn't show or illustrate is that the original Lucas switches had a very different internal design and they lasted for decades without issue. These old switches did "snap" shut thus minimising any potential for internal arcing.

https://mgaguru.com/mgtech/electric/et119g.htm

Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
mrs.smith2012
Minor Addict
Posts: 502
Joined: Wed Sep 17, 2025 6:19 pm
Location: Essex
MMOC Member: Yes

Re: Blowing fuses… help!

Post by mrs.smith2012 »

So just to clarify, my switch is at fault and the wiring it probably okay? Or is it possible there is issue with the wiring hence why the switch has failed?

I really appreciate everyone’s advice on this, and I shall take a look at those articles attached :tu1:
User avatar
geoberni
Minor Maniac
Posts: 5337
Joined: Fri Aug 04, 2017 11:19 am
Location: North Leicestershire
MMOC Member: Yes

Re: Blowing fuses… help!

Post by geoberni »

mrs.smith2012 wrote: ↑Thu Nov 19, 2026 6:40 pm So just to clarify, my switch is at fault and the wiring it probably okay? Or is it possible there is issue with the wiring hence why the switch has failed?

I really appreciate everyone’s advice on this, and I shall take a look at those articles attached :tu1:
The first one. :wink:
Basil the 1955 series II

Image
User avatar
svenedin
Minor Legend
Posts: 4973
Joined: Fri Aug 29, 2014 9:27 am
Location: Surrey
MMOC Member: Yes

Re: Blowing fuses… help!

Post by svenedin »

mrs.smith2012 wrote: ↑Thu Nov 19, 2026 6:40 pm So just to clarify, my switch is at fault and the wiring it probably okay? Or is it possible there is issue with the wiring hence why the switch has failed?

I really appreciate everyone’s advice on this, and I shall take a look at those articles attached :tu1:
Yes your switch is at fault. The buzzer in the boot area is unlikely to have had anything to do with the failure as such buzzers draw a tiny current in comparison to the current drawn by the brake light bulbs. Without actually being able to see and test the wiring in the boot nobody can guarantee that there is no fault there which is why I suggested that the ridiculous and unnecessary wiring is removed.

As Berni says, some strange things have been done to your car by the previous owner and in due course it may be a good idea to address these issues. I would definitely have a look at the amp ratings of the fuses in the additional fuse box. If the amp rating is too high, the wiring can melt and catch fire in the event of a short rather than the fuse blowing as it should.

Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.

Stephen
Post Reply