Blowing fuses… help!
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
-
mrs.smith2012
- Minor Addict
- Posts: 502
- Joined: Wed Sep 17, 2025 6:19 pm
- Location: Essex
- MMOC Member: Yes
Blowing fuses… help!
Morning all,
I was out on a drive when I lost my indicators, I had also noticed my fuel gauge was sitting on empty even though I knew she had almost half a tank.
Long story short, got home, tested a few other things and realised I had no wipers or brake lights. My side lights and hazards are working.
Found the culprit, the bottom fuse had blown, so it was replaced, but immediately blew again on ignition.
So now I’m under the hood, looking at the electrics trying to see if anything is amiss… I can’t see any obvious loose wires or corrosion - I did get a ready low resistance reading when I checked the fuse terminal… so I think there must be a short somewhere but where?
One piece of advice I did get was to disconnect and clean all the terminals… but do they mean the ones on the unit above the fuse box?
Obviously I’m not an electrician, so I’m not going to go pulling wires about, but I’d like to do as much basic troubleshooting as I can before I call an professional, in case it is something extremely simple!
Any advice would be welcomed, have attached a pic of Nell’s ‘electrical area’
I will say too, shes been converted to negative earth, has an alternator and indicators instead of her original trafficators. She also has a remote immobiliser fitted, which I’m not sure if that’s relevant or not.
Thanks
Sarah
I was out on a drive when I lost my indicators, I had also noticed my fuel gauge was sitting on empty even though I knew she had almost half a tank.
Long story short, got home, tested a few other things and realised I had no wipers or brake lights. My side lights and hazards are working.
Found the culprit, the bottom fuse had blown, so it was replaced, but immediately blew again on ignition.
So now I’m under the hood, looking at the electrics trying to see if anything is amiss… I can’t see any obvious loose wires or corrosion - I did get a ready low resistance reading when I checked the fuse terminal… so I think there must be a short somewhere but where?
One piece of advice I did get was to disconnect and clean all the terminals… but do they mean the ones on the unit above the fuse box?
Obviously I’m not an electrician, so I’m not going to go pulling wires about, but I’d like to do as much basic troubleshooting as I can before I call an professional, in case it is something extremely simple!
Any advice would be welcomed, have attached a pic of Nell’s ‘electrical area’
I will say too, shes been converted to negative earth, has an alternator and indicators instead of her original trafficators. She also has a remote immobiliser fitted, which I’m not sure if that’s relevant or not.
Thanks
Sarah
Re: Blowing fuses… help!
I don't like the look of this wire , going through the metal ferrule with no grommet. What is this added upper fuse box feeding?
- Attachments
-
- Fuse box.jpg (78.46 KiB) Viewed 502 times
-
mrs.smith2012
- Minor Addict
- Posts: 502
- Joined: Wed Sep 17, 2025 6:19 pm
- Location: Essex
- MMOC Member: Yes
Re: Blowing fuses… help!
Honestly I don’t know - sorry that sounds incredibly ignorant doesn’t it
So the upper fuse box case is not original?
I can try and have a closer look and see where those wires are heading…
So the upper fuse box case is not original?
I can try and have a closer look and see where those wires are heading…
- svenedin
- Minor Legend
- Posts: 4972
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: Blowing fuses… help!
The upper fuse box is definitely not original. You could disconnect that wire from the fuse box and find out what does not work as well as whether the fuse still continue to blow. Then you have found your fault.mrs.smith2012 wrote: ↑Wed Nov 18, 2026 11:52 am Honestly I don’t know - sorry that sounds incredibly ignorant doesn’t it![]()
So the upper fuse box case is not original?
I can try and have a closer look and see where those wires are heading…
Which fuse is blowing? It it the lower one in the original fuse box?
Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
-
mrs.smith2012
- Minor Addict
- Posts: 502
- Joined: Wed Sep 17, 2025 6:19 pm
- Location: Essex
- MMOC Member: Yes
Re: Blowing fuses… help!
Yes,the bottom fuse in the original fuse box is the one that’s blowing.
That was my next plan, to take out the fuses in that top box and see what works and what doesn’t!
That was my next plan, to take out the fuses in that top box and see what works and what doesn’t!
- svenedin
- Minor Legend
- Posts: 4972
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: Blowing fuses… help!
Ok. That is helpful. We can't tell you what is connected to your new fuse box but we can tell you what is connected to the original fuse box as that is as per the wiring diagram.mrs.smith2012 wrote: ↑Wed Nov 18, 2026 12:37 pm Yes,the bottom fuse in the original fuse box is the one that’s blowing.
That was my next plan, to take out the fuses in that top box and see what works and what doesn’t!
Just out of interest, where is the supply to the new fuse box coming from? It looks like a black and white wire in the photo joining the new fuse box at the top left.
It seems at first look like it is not related to your new fuse box.
Silly question perhaps but are you sure the new fuse you are fitting is of sufficient amp rating? Should be 35 amps. We cannot take anything for granted!
Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
-
jaekl
- Minor Addict
- Posts: 724
- Joined: Thu Jun 19, 2008 7:40 pm
- Location: Pennsylvania, USA
- MMOC Member: No
Re: Blowing fuses… help!
Because the wiper motor is always powered when the ignition is on, removing the green wire from the wiper motor would eliminate one of the first suspects. The next one is the is the wire to the light at the end of the turn indicator stalk.
-
mrs.smith2012
- Minor Addict
- Posts: 502
- Joined: Wed Sep 17, 2025 6:19 pm
- Location: Essex
- MMOC Member: Yes
Re: Blowing fuses… help!
Not a silly question at all! Yes I tried two fuses, both 35amp, which is what was in there originally.
So the wire you mentioned runs into this thing here?
So the wire you mentioned runs into this thing here?
-
mrs.smith2012
- Minor Addict
- Posts: 502
- Joined: Wed Sep 17, 2025 6:19 pm
- Location: Essex
- MMOC Member: Yes
Re: Blowing fuses… help!
Interesting you say that, as I actually used my wipers for the first time Iong time… they worked… but somewhere along the drive the fuse blew, and by the time I reached home they weren’t working. I’ll try that thanks
- svenedin
- Minor Legend
- Posts: 4972
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: Blowing fuses… help!
That's fine. It's just picking up the battery feed from there (battery side of solenoid).mrs.smith2012 wrote: ↑Wed Nov 18, 2026 12:54 pm Not a silly question at all! Yes I tried two fuses, both 35amp, which is what was in there originally.
So the wire you mentioned runs into this thing here?
IMG_9366.jpeg
Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
-
mrs.smith2012
- Minor Addict
- Posts: 502
- Joined: Wed Sep 17, 2025 6:19 pm
- Location: Essex
- MMOC Member: Yes
Re: Blowing fuses… help!
Okay thank you… I’ve tried isolating the wiper motor, as thought that might be a culprit… fuse still blew on ignition same as before
I’ve also identified what the other fuse box is feeding. My hazard lights, headlights and I think the washer jet motor.. as well as the immobiliser… none of these things stop working with the other fuse box blown, so I don’t think they are connected, but I don’t know
I’ve also identified what the other fuse box is feeding. My hazard lights, headlights and I think the washer jet motor.. as well as the immobiliser… none of these things stop working with the other fuse box blown, so I don’t think they are connected, but I don’t know
- svenedin
- Minor Legend
- Posts: 4972
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: Blowing fuses… help!
They’re not connected so ignore the additional fuse box. It’s not the issue.mrs.smith2012 wrote: ↑Wed Nov 18, 2026 2:37 pm Okay thank you… I’ve tried isolating the wiper motor, as thought that might be a culprit… fuse still blew on ignition same as before![]()
I’ve also identified what the other fuse box is feeding. My hazard lights, headlights and I think the washer jet motor.. as well as the immobiliser… none of these things stop working with the other fuse box blown, so I don’t think they are connected, but I don’t know
The wiper motor has 3 connections. Permanent earth (black), switched earth (green/black), permanent live (green). Remove the green wire from the motor.
To check that the short isn’t being caused by a frayed wire going up the indicator stalk, remove the power from the flasher can on the bulkhead, dark green wire (no trace colour)
Stephen
Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
-
mrs.smith2012
- Minor Addict
- Posts: 502
- Joined: Wed Sep 17, 2025 6:19 pm
- Location: Essex
- MMOC Member: Yes
Re: Blowing fuses… help!
Thanks for the feedback everyone!
So I’m now 99.9% sure it’s my brake lights!
So job tomorrow (when it’s light) is to check all the wiring connected with the brake lights and see if there is any obvious issues
Not solved yet but getting somewhere!
So I’m now 99.9% sure it’s my brake lights!
So job tomorrow (when it’s light) is to check all the wiring connected with the brake lights and see if there is any obvious issues
Not solved yet but getting somewhere!
- svenedin
- Minor Legend
- Posts: 4972
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: Blowing fuses… help!
Ok. Well done, good progress.
Stephen
Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
-
mike1864
- Minor Fan
- Posts: 463
- Joined: Tue May 17, 2011 10:06 pm
- Location: Hertfordshire
- MMOC Member: Yes
Re: Blowing fuses… help!
I'd suggest buying a portable Digital Voltmeter (DVM). These days they are not much more than a tenner. Even if you're not electrically savvy, with the aid of one of these - and some guidance from members of this forum - it will make diagnostics so much easier.
Not only will it show you where volts are getting to, its resistance range will (with care) identify components or wires that are shorting to chassis (which is what is making your fuses blow).
Not only will it show you where volts are getting to, its resistance range will (with care) identify components or wires that are shorting to chassis (which is what is making your fuses blow).
- svenedin
- Minor Legend
- Posts: 4972
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: Blowing fuses… help!
If you are sure it is something to do with the brake lights, check the entire circuit. Not just the wiring (looking for chafing that could short) but the bulb holders and their connections too. I am not sure how you would instantly blow a fuse when turning on the ignition if you are not activating the brake switch. No power should be going to the brake lights in this situation but there will be power to the brake light switch (green wire). Green/purple wire sends power to the brake lamps only when the switch is activated by pressure on the brake pedal. In rare situations the brake light switch can fail internally in a permanently on state. Usually they fail permanently open.
To test for a fault with brake lights remove the green wire from the pressure switch located on the floor of the engine bay near the radiator. Fit a new fuse and see if it blows. Of course this doesn't exclude a short between the fusebox and the switch.
Let's narrow it down. It is something to do with 1 of the 3 green wires which are on the load side of the fuse. Those 3 green wires supply:
1) Brake light switch
2) Indicator flasher can
3) Instrument voltage stabiliser (attached to the speedo and then supplies the fuel gauge)
So a possibility is the instrument voltage stabiliser has failed or a wire has come adrift causing a short behind the speedo or an issue with the wire that connects to the fuel tank sender on top of the fuel tank.
Needs some detective work.
Stephen
To test for a fault with brake lights remove the green wire from the pressure switch located on the floor of the engine bay near the radiator. Fit a new fuse and see if it blows. Of course this doesn't exclude a short between the fusebox and the switch.
Let's narrow it down. It is something to do with 1 of the 3 green wires which are on the load side of the fuse. Those 3 green wires supply:
1) Brake light switch
2) Indicator flasher can
3) Instrument voltage stabiliser (attached to the speedo and then supplies the fuel gauge)
So a possibility is the instrument voltage stabiliser has failed or a wire has come adrift causing a short behind the speedo or an issue with the wire that connects to the fuel tank sender on top of the fuel tank.
Needs some detective work.
Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
-
mrs.smith2012
- Minor Addict
- Posts: 502
- Joined: Wed Sep 17, 2025 6:19 pm
- Location: Essex
- MMOC Member: Yes
Re: Blowing fuses… help!
Thank you for the advice everyone.
I was mistaken when I said the fuse was blowing on ignition… it wasn’t. I didn’t give it a thought but I tend to put my foot on the brake before I even start her, a habit from driving the modern car… so of course the brake was engaged on ignition.
I tried switching ignition on and starting her up without touching anything, fuse was fine… the moment I engaged the brake it went.
Now I’m out of fuses but when my delivery arrives tomorrow I do want to test everything else.. indicators, wipers etc as I don’t want to assume it is ONLY the brakes blowing the fuse. But the brakes are the likely culprit right now.
On inspection the brake light switch looks okay and the wires and connectors look fine, just dirty. I plan to clean them with a bit of contact spray but I’m not convinced this is it.
I checked the bulbs and wiring inside the rear lights, all looks intact… tracing the wires back into the boot reveals no obvious exposed or melted wiring… although it could be hidden as some of the wiring is insulated.
The only thing that is really standing out to me right now is this thing… which I’m hoping someone can identify as I have no idea what it is… it appears to be some kind of aftermarket device that somebody has wired in. One wire runs down into the boot… I need to try and trace where it goes… the other appears to be wired into the brake light circuit?? What is this thing?
I was mistaken when I said the fuse was blowing on ignition… it wasn’t. I didn’t give it a thought but I tend to put my foot on the brake before I even start her, a habit from driving the modern car… so of course the brake was engaged on ignition.
I tried switching ignition on and starting her up without touching anything, fuse was fine… the moment I engaged the brake it went.
Now I’m out of fuses but when my delivery arrives tomorrow I do want to test everything else.. indicators, wipers etc as I don’t want to assume it is ONLY the brakes blowing the fuse. But the brakes are the likely culprit right now.
On inspection the brake light switch looks okay and the wires and connectors look fine, just dirty. I plan to clean them with a bit of contact spray but I’m not convinced this is it.
I checked the bulbs and wiring inside the rear lights, all looks intact… tracing the wires back into the boot reveals no obvious exposed or melted wiring… although it could be hidden as some of the wiring is insulated.
The only thing that is really standing out to me right now is this thing… which I’m hoping someone can identify as I have no idea what it is… it appears to be some kind of aftermarket device that somebody has wired in. One wire runs down into the boot… I need to try and trace where it goes… the other appears to be wired into the brake light circuit?? What is this thing?
-
mrs.smith2012
- Minor Addict
- Posts: 502
- Joined: Wed Sep 17, 2025 6:19 pm
- Location: Essex
- MMOC Member: Yes
Re: Blowing fuses… help!
I have one! Although I haven’t got to the stage of checking the wires with it yet, just visually inspecting at the momentmike1864 wrote: ↑Thu Nov 19, 2026 10:27 am I'd suggest buying a portable Digital Voltmeter (DVM). These days they are not much more than a tenner. Even if you're not electrically savvy, with the aid of one of these - and some guidance from members of this forum - it will make diagnostics so much easier.
Not only will it show you where volts are getting to, its resistance range will (with care) identify components or wires that are shorting to chassis (which is what is making your fuses blow).
-
mike1864
- Minor Fan
- Posts: 463
- Joined: Tue May 17, 2011 10:06 pm
- Location: Hertfordshire
- MMOC Member: Yes
Re: Blowing fuses… help!
It's not clear what this module is; more photos needed.
Maybe it's part of extra cabling from the previous owner (PO) fitting a high level brake light?
Or maybe the PO had wired in a dashboard switch to work the brake lights to ward off tailgaters; naughty!
Either way I'd disconnect it from the brake circuit.
Then, with the ignition OFF, measure the resistance between the terminals on this module and a solid chassis point.
If it reads low ohms (especially under 1 ohm), it suggests this add-on was the culprit.
Maybe it's part of extra cabling from the previous owner (PO) fitting a high level brake light?
Or maybe the PO had wired in a dashboard switch to work the brake lights to ward off tailgaters; naughty!
Either way I'd disconnect it from the brake circuit.
Then, with the ignition OFF, measure the resistance between the terminals on this module and a solid chassis point.
If it reads low ohms (especially under 1 ohm), it suggests this add-on was the culprit.
- svenedin
- Minor Legend
- Posts: 4972
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: Blowing fuses… help!
You can buy glass fuses in Halfords if that's any help. Some motor factors stock them but not all as modern cars use blade fuses.
I think you have one spare fuse which I can see in the fuse box end-on in your photo.....
I've no idea what the PO has installed there but it seems to be the issue. If it doesn't work, whatever it is, can you disconnect it? Is it a buzzer of some kind?
Stephen
I think you have one spare fuse which I can see in the fuse box end-on in your photo.....
I've no idea what the PO has installed there but it seems to be the issue. If it doesn't work, whatever it is, can you disconnect it? Is it a buzzer of some kind?
Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
