Reducing dif whine
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
Reducing dif whine
Dear all,
If I renew sun and planet gears, planet gears shaft, and the 4 bronze washers, will the dif whine be noticeable reduced?
If I renew sun and planet gears, planet gears shaft, and the 4 bronze washers, will the dif whine be noticeable reduced?
Finished rescuing a 1967 2-door. Define finished....
Re: Reducing dif whine
Les, no mixing,, all new from ESM, gears, shaft, bronze. Noticeable reduced whining?
Finished rescuing a 1967 2-door. Define finished....
Re: Reducing dif whine
For clarification, if the teeth of any new gear mesh with the teeth of any original gear a whine is likely, for the simple reason, gears wear together as sets. However if all the meshing teeth are new, you can’t do any more.
Re: Reducing dif whine
I have a whining dif. Just wear and old. If I put those NEW parts in, will that noticeable reduce the whining.
Finished rescuing a 1967 2-door. Define finished....
-
- Minor Fan
- Posts: 104
- Joined: Fri Nov 10, 2023 8:42 am
- Location: Chilmark, Wiltshire
- MMOC Member: Yes
Re: Reducing dif whine
I know many people get a bit uppity on such things, but I have used Molyslip gearbox for decades to reduce or even eliminate noisy diff and gearbox whine in bikes and cars.
It's worth a try, and may resolve your issue....
Jon
It's worth a try, and may resolve your issue....
Jon
-
- Minor Fan
- Posts: 461
- Joined: Wed Jun 07, 2017 11:37 pm
- Location: Carmarthenshire
- MMOC Member: No
Re: Reducing dif whine
I’m no expert, but sun and planet gears won’t make a diff whine, they only turn slowly when cornering.
The whine comes from the crown wheel and pinion, could be worn, could need setting up.
Regards John
The whine comes from the crown wheel and pinion, could be worn, could need setting up.
Regards John
Re: Reducing dif whine
Good idea! I'll try this Jon.
Finished rescuing a 1967 2-door. Define finished....
Re: Reducing dif whine
This are the answers I was looking for. Thanks John.StillGotMy1stCar wrote: ↑Wed Jun 26, 2024 7:21 pm I’m no expert, but sun and planet gears won’t make a diff whine, they only turn slowly when cornering.
The whine comes from the crown wheel and pinion, could be worn, could need setting up.
Regards John
Finished rescuing a 1967 2-door. Define finished....
- Bill_qaz
- Minor Addict
- Posts: 891
- Joined: Fri Jan 14, 2022 7:31 pm
- Location: Oxfordshire
- MMOC Member: Yes
Re: Reducing dif whine
Is you whine worse on drive or overrun?
Have you measured the back lash at the input.
Would agree Sun and planet gears very rarely cause a whine as driving straight they are not under any load, pinion the crownwheel set up or bearing are more likely.
Have you measured the back lash at the input.
Would agree Sun and planet gears very rarely cause a whine as driving straight they are not under any load, pinion the crownwheel set up or bearing are more likely.
Regards Bill
Re: Reducing dif whine
I've put new bronze in and the backlash at the driveshaft flange has been halved. Whine only when driving. Worst at 50-ish mph. Otherwise it is an untouched dif . Must be the bearings then. Molyslip advice seems worth trying.
Finished rescuing a 1967 2-door. Define finished....
- Bill_qaz
- Minor Addict
- Posts: 891
- Joined: Fri Jan 14, 2022 7:31 pm
- Location: Oxfordshire
- MMOC Member: Yes
Re: Reducing dif whine
Are you sure it's not a wheel bearing?
What do you mean by new bronze? It's pinion and crownwheel setting that control backlash.
Regards Bill
Re: Reducing dif whine
The bronze thrust washers of sun- and planet gears. Specially the ones from the planet gears can be worn, so the gears can slide on its shaft. I saw this sliding taking up some slack when you move the driving flange back and forth. But I suppose slack is everywhere in my dif
Finished rescuing a 1967 2-door. Define finished....
-
- Minor Legend
- Posts: 1728
- Joined: Thu May 12, 2016 6:33 am
- MMOC Member: No
Re: Reducing dif whine
It won’t necessarily sort the problem. The most likely source of diff whine is the crown-wheel and pinion clearances. It’s a precision job setting up the difg.