interchangeable engines?

Discuss mechanical problems here.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
Post Reply
vibrodolly
Minor Friendly
Posts: 83
Joined: Wed Jul 13, 2005 11:21 am
MMOC Member: No

interchangeable engines?

Post by vibrodolly »

My 1958 948cc saloon's engine is on it's last legs, methinks.

I have a good 1098 engine (and gearbox) rebuilt 5000 miles ago only.

Can these engines be swapped over without modification to the mounts etc?
Can I do just the engine or the gearbox as well. I even have a 1098 drive shaft if they are different.

You expertise and knowledge would be appreciated.
Thanks
Nick
ampwhu
Minor Addict
Posts: 769
Joined: Sat Oct 31, 2009 8:51 pm
Location: Epsom, Surrey
MMOC Member: No

Re: interchangeable engines?

Post by ampwhu »

use the back plate from the engine to match the gearbox. so use 948 back plate on the 1098 engine. use the 948 clutch.
myoldjalopy
Minor Legend
Posts: 3026
Joined: Tue Jan 29, 2013 10:32 pm
Location: Kernow
MMOC Member: Yes

Re: interchangeable engines?

Post by myoldjalopy »

Easiest and best way - just replace the 948 engine and its box with the 1098 engine with its box. Straight swap..... :D
vibrodolly
Minor Friendly
Posts: 83
Joined: Wed Jul 13, 2005 11:21 am
MMOC Member: No

Re: interchangeable engines?

Post by vibrodolly »

I can "easily" change a 1098 gearbox and engine for the 948.
Is the drive shaft the same?

Nick
myoldjalopy
Minor Legend
Posts: 3026
Joined: Tue Jan 29, 2013 10:32 pm
Location: Kernow
MMOC Member: Yes

Re: interchangeable engines?

Post by myoldjalopy »

Driveshaft/prop shaft is the same. You may want to consider fitting a 1098 (4.22) diff as well. It will accelerate well with the 948 (4.55) diff but the engine will be a bit thrashy at top speeds.......
You also might consider fitting the larger 8" front brake drums, and shoes, if you still have 7" ones fitted in front, to give better braking with the larger engine's increased power.
vibrodolly
Minor Friendly
Posts: 83
Joined: Wed Jul 13, 2005 11:21 am
MMOC Member: No

Re: interchangeable engines?

Post by vibrodolly »

Well, I don't think I need to change the engine. After lots of faffing, I decided to whip the head off today. I found that only 3/4 of one of the exhaust valves was present. No wonders it's been feeling a little lack lustre.

How common is it that valves disintegrate?
Where on earth did the bit go? I didn't fine it.

Engine much better now.

Thanks.
dalebrignall
Minor Legend
Posts: 2528
Joined: Fri Aug 03, 2007 4:06 pm
Location: stalbans
MMOC Member: No

Re: interchangeable engines?

Post by dalebrignall »

hopefully it went out of the exhaust pipe the unleaded fuel burns much hotter than the old 4 star and if the head has not been converted to unleaded then the valves can burn out glad your sorted
[sig]5641[/sig]
vibrodolly
Minor Friendly
Posts: 83
Joined: Wed Jul 13, 2005 11:21 am
MMOC Member: No

Re: interchangeable engines?

Post by vibrodolly »

Thanks - but to be fair it was an unleaded head, perhaps 15000 miles ago.
From a well know internet seller and own website.
Also had valve springs break on this head.
Not sure about the quality of this restoration on the head.

Lucky I had a spare valve.
It's soooo much better.
Post Reply