Timeing chain
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
-
- Minor Fan
- Posts: 108
- Joined: Mon May 20, 2013 3:30 pm
- MMOC Member: No
Timeing chain
Hi i have got a 69 traveller and have bought a duplex timing chain. I have been trying to get all my info together before i start to fit it and have noticed that someone on the net has mentioned you need to fit a tensioner, i wanted to know if this is correct as i was advised at david manners that the duplex kit was the best and there was no need for the use of a tensioner. THANKS
-
- Minor Maniac
- Posts: 10909
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Timeing chain
It is not essential to fit a tensioner if you fit a duplex timing chain.
If you fit a duplex kit you can have either the duplex and no tensioner or the duplex and tensioner.
If you fit just the duplex you can use the Minor timing chain cover (the later version with the lip seal is best).
If you want the duplex with tensioner you will have to fit the Mini Metro type timing chain cover.
Either way is much better than the original Minor set up with twin rubber timing chain tensioner rings.
On my Minor I currently have the duplex with tensioner but have run a duplex without the tensioner but prefer the duplex with tensioner.
http://www.ebay.co.uk/itm/CLASSIC-MINI- ... 35e7046fb8
http://www.ebay.co.uk/itm/CLASSIC-MINI- ... 4d2f6db690
If you fit a duplex kit you can have either the duplex and no tensioner or the duplex and tensioner.
If you fit just the duplex you can use the Minor timing chain cover (the later version with the lip seal is best).
If you want the duplex with tensioner you will have to fit the Mini Metro type timing chain cover.
Either way is much better than the original Minor set up with twin rubber timing chain tensioner rings.
On my Minor I currently have the duplex with tensioner but have run a duplex without the tensioner but prefer the duplex with tensioner.
http://www.ebay.co.uk/itm/CLASSIC-MINI- ... 35e7046fb8
http://www.ebay.co.uk/itm/CLASSIC-MINI- ... 4d2f6db690
Re: Timeing chain
The Mini tensioner system is by far the best for a standard engine. It was standardised by MG/Rover for good reason. Duplex is necessary for high lift cams and stupidly hard valve springs.... You 'can' fit a tensioner with duplex - but when I tried it the rubber pad disintegrated almost immediately - perhaps I had too much tension on it. If you have already bought the duplex, then I guess you had better carry on and fit it. Be sure to countersink the holes in the front plate enough....
Re: Timeing chain
Does your set includes the 2 countersunk screws?
One of them visible on this picture:
[frame][/frame]
One of them visible on this picture:
[frame][/frame]
_________________________________________________________________
http://morrisminortourer.blogspot.nl
http://morrisminortourer.blogspot.nl
Re: Timeing chain
I'm not sure that one is coutersunk enough...it must be very close...and if there is a 'link' in the chain...... I prefer to make sure they are completely flush with the front plate...
-
- Minor Maniac
- Posts: 10909
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Timeing chain
These are the screws you need when fitting a duplex timing chain.
http://www.minispares.com/product/Class ... .aspx|Back to
I use LOCTITE 243 'Lock 'N Seal to secure the screws in place - and as bmc says make sure that they are well countersunk.
If there is a link in the chain make sure that the closed end is at the direction of travel and it is on the timing cover side of the chain.
http://www.minispares.com/product/Class ... .aspx|Back to
I use LOCTITE 243 'Lock 'N Seal to secure the screws in place - and as bmc says make sure that they are well countersunk.
If there is a link in the chain make sure that the closed end is at the direction of travel and it is on the timing cover side of the chain.
Re: Timeing chain
You are right. I had to buy a proper countersink drill to do a better job.bmcecosse wrote:I'm not sure that one is coutersunk enough...it must be very close...and if there is a 'link' in the chain...... I prefer to make sure they are completely flush with the front plate...
Remember the one on the side of the front plate left very little steel on one side.
No picture of the better version...
_________________________________________________________________
http://morrisminortourer.blogspot.nl
http://morrisminortourer.blogspot.nl
-
- Minor Maniac
- Posts: 10909
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Timeing chain
This is the type of 90 degree 13mm/1/2" countersink drill that you need:-
http://www.ebay.co.uk/itm/Faithfull-13m ... 5636447153
You cannot use a normal drill to countersink as the tip of the drill for general work is ground at 118 degrees.
As Theo says - take care not to break through the metal because it does get quite thin in the area of the top of the hole when countersunk.
The countersunk screws can be supplied in two lengths 12mm O/L and 16mm O/L. Ensure that the length you have is adequate for the job. I have both lengths available to use but my preference is to fit the 16mm O/L ones. Make sure that the 16mm O/L ones do not bottom out in the front bearing cap.[frame][/frame]
Some of the Allen screws now supplied have quite thick heads and there may be a need to face off the Allen screws in the lathe.[frame][/frame]
http://www.ebay.co.uk/itm/Faithfull-13m ... 5636447153
You cannot use a normal drill to countersink as the tip of the drill for general work is ground at 118 degrees.
As Theo says - take care not to break through the metal because it does get quite thin in the area of the top of the hole when countersunk.
The countersunk screws can be supplied in two lengths 12mm O/L and 16mm O/L. Ensure that the length you have is adequate for the job. I have both lengths available to use but my preference is to fit the 16mm O/L ones. Make sure that the 16mm O/L ones do not bottom out in the front bearing cap.[frame][/frame]
Some of the Allen screws now supplied have quite thick heads and there may be a need to face off the Allen screws in the lathe.[frame][/frame]
Last edited by philthehill on Mon Mar 30, 2015 9:18 pm, edited 2 times in total.
-
- Minor Fan
- Posts: 108
- Joined: Mon May 20, 2013 3:30 pm
- MMOC Member: No
Re: Timeing chain
Wow many thanks for all the advice they did supply the two little screws with the kit. when i purchased it from david manners i was going to buy just a replacement standard chain but they did not have any in stock and the guy said no one fits them any more as they always sell the duplex.I also had the oil seal in the kit which is handy as the one on my car is leaking badly.Thanks again for all the help its invaluable.
Re: Timeing chain
It's certainly not true that 'no one fits the standard chain any more' - you have to remember these people are SALESMEN..... In fact the Mini single chain with tensioner set up is far quieter in the long run. But does require purchase of a different chain cover with 'side bump' of course... So it's not the cheapest option if you buy all new parts.
-
- Minor Maniac
- Posts: 10909
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: Timeing chain
It should be noted that when fitting the duplex timing chain with tensioner and using the later type timing cover with breather that has either the sensor mounting or indent to accommodate the sensor the indent can foul the duplex timing chain. The indent must be removed to clear the chain. Mini Spares recommend tapping the indent flat.
The indent can be seen at the top L/H corner of the attached photograph protruding into the timing chain cover.
The earlier timing chain cover without sensor bracket or indent will fit without any modification.
http://www.minispares.com/product/Class ... sic/timing chain cover.aspx|Back to search[frame][/frame]
The indent can be seen at the top L/H corner of the attached photograph protruding into the timing chain cover.
The earlier timing chain cover without sensor bracket or indent will fit without any modification.
http://www.minispares.com/product/Class ... sic/timing chain cover.aspx|Back to search[frame][/frame]