Is this rubber 'bit' available?

Discuss Bodywork problems here.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
Post Reply
Arthurdaily
Minor Addict
Posts: 636
Joined: Tue May 24, 2011 4:25 pm
MMOC Member: No

Is this rubber 'bit' available?

Post by Arthurdaily »

I am sorting out my doors on my restoration - but am wondering about the bottom area of the rear window frame strut... I have seen many cars with a sort of small rubber seal that sits between the strut and the car door - but I haven't got any on my car - are they an actual 'part' or do people just make 'em?

Thanks![frame]Image[/frame]
chickenjohn
Minor Legend
Posts: 4064
Joined: Tue Dec 07, 2004 8:50 am
Location: Margate, East Kent
MMOC Member: No

Re: Is this rubber 'bit' available?

Post by chickenjohn »

Yes, those seals should be present- and they are available check ESM? bull Motif or your favourite supplier.
Cheers John - all comments IMHO
- Come to this years Kent branches Hop rally! http://www.kenthop.co.uk
(check out the East Kent branch website http://www.ekmm.co.uk )
ImageImage
Arthurdaily
Minor Addict
Posts: 636
Joined: Tue May 24, 2011 4:25 pm
MMOC Member: No

Re: Is this rubber 'bit' available?

Post by Arthurdaily »

Hi, thanks - can't find 'em listed with BM or ESM - Moss seems to have them on a schematic but no price, will have to ring. Thanks Chicken!
mike.perry
Series MM Registrar
Posts: 10183
Joined: Sun Jul 24, 2005 11:39 pm
Location: Reading
MMOC Member: No

Re: Is this rubber 'bit' available?

Post by mike.perry »

I squirted some silicone sealant in the gap to stop the draft
[sig]3580[/sig]
irmscher
Minor Legend
Posts: 3773
Joined: Wed Jul 14, 2010 10:53 am
Location: South Manchester
MMOC Member: Yes

Re: Is this rubber 'bit' available?

Post by irmscher »

I thought you were restoring a blue car
chickenjohn
Minor Legend
Posts: 4064
Joined: Tue Dec 07, 2004 8:50 am
Location: Margate, East Kent
MMOC Member: No

Re: Is this rubber 'bit' available?

Post by chickenjohn »

Here it is on ESM (if it is the seal I think you mean), only £1.50 plus VAT and postage.

http://morrisminorspares.co.uk/shop/pro ... 11e2ee002d

Image
Cheers John - all comments IMHO
- Come to this years Kent branches Hop rally! http://www.kenthop.co.uk
(check out the East Kent branch website http://www.ekmm.co.uk )
ImageImage
Neil MG
Minor Legend
Posts: 1116
Joined: Sat Jan 15, 2011 8:05 am
Location: Cumbria
MMOC Member: No

Re: Is this rubber 'bit' available?

Post by Neil MG »

chickenjohn wrote:Here it is on ESM (if it is the seal I think you mean), only £1.50 plus VAT and postage.

http://morrisminorspares.co.uk/shop/pro ... 11e2ee002d

Image
No, that one is for the quarter light. There is a short section of edge seal that should be (was originally from the factory) fitted in that gap, but I can't see it on any of the usual suppliers websites.
1956 Morris Minor Series II
1959 MGA 1600 Roadster
1966 Jaguar Mk2 3.8 MOD
Arthurdaily
Minor Addict
Posts: 636
Joined: Tue May 24, 2011 4:25 pm
MMOC Member: No

Re: Is this rubber 'bit' available?

Post by Arthurdaily »

Yes, it is the smaller one I'm after... I'll have to make some me thinks!

It was a blue car Irmscher... now red... mostly...
Declan_Burns
Minor Legend
Posts: 1962
Joined: Wed Apr 18, 2007 7:32 am
Location: Düsseldorf, Germany
MMOC Member: No

Re: Is this rubber 'bit' available?

Post by Declan_Burns »

I think this is the seal in question and I don't think they are available as I asked the same question a few years back. They should be easy to make from 1mm rubber or an offcut from the seal from the door to the sill which has a similar profile and could be cut back. I'll have a look at doing it over the weekend. I repaired the one in the photo with silicon sealer at the time.
Regards
Declan[frame]Image[/frame]


Regards
Declan
chickenjohn
Minor Legend
Posts: 4064
Joined: Tue Dec 07, 2004 8:50 am
Location: Margate, East Kent
MMOC Member: No

Re: Is this rubber 'bit' available?

Post by chickenjohn »

Interesting, I don't think I've ever seen (or perhaps just not noticed) a Minor with a seal in that part of the door before, perhaps an owner modification to keep water out of the door (and thus keep rust at bay!)

If so, a good idea, if it works.
aupickup
Minor Maniac
Posts: 6004
Joined: Tue Jul 20, 2004 11:41 pm
Location: lanark
MMOC Member: No

Re: Is this rubber 'bit' available?

Post by aupickup »

i have them on my 2 door
Post Reply