Brake light switch

Discuss other problems here.
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
Post Reply
Jefftav
Minor Addict
Posts: 720
Joined: Fri Mar 28, 2003 9:28 am
Location: Inverness
MMOC Member: No

Brake light switch

Post by Jefftav »

I need to change my BL switch and I was told to hold the pedal down for 5mins and keep it held down whilst unscrewing the switch from the junction beside the radiator. Just I would have thought it should be the opposite as holding the pedal down will push fluid out when I unscrew the switch.

Can anyone keep me right with this? Thanks in advance, Jeff
Image
Dean
Minor Legend
Posts: 2180
Joined: Fri May 30, 2008 9:41 pm
Location: Sutton Coldfield
MMOC Member: No

Re: Brake light switch

Post by Dean »

I'm inclined to agree with your observation. The switch works off pressure, therefore pushing the pedal down to put the brake lights on and unscrewing will result in brake fluid in your face.

Im thinking, boil a kettle of water and keep to hand. Take your brake master cylinder cap off and put some clingfilm over the hole, then screw on the top to create a vacuum in the brake system. Undo the brake light switch... carefully with a rag around to capture any leakage. replace with new oil pressure switch, pour boiled water over any spilt brake fluid on body work and wipe clean. Remove cling film from master cylinder. If there is leakage you may have to bleed the brakes again.

Never tried it, but it's the way I'd attempt it.
My Minor:
A Clarendon Grey 1953 4 Door Series II.
MMOC - 66535


alanworland
Minor Legend
Posts: 1453
Joined: Tue Jan 30, 2007 10:09 pm
Location: Essex
MMOC Member: No

Re: Brake light switch

Post by alanworland »

Just changed mine (it packed up after 58 years!)
I just unscrewed it with a bit of rag around the fitting, hardly anything come out - I filled the new switch with brake fluid (I use silicone) and screwed it in - didn't even have to bleed it!
I did find the new switch although having a tapered thread 'bottomed out' before screwing tight - I fitted a soft copper washer which sealed the switch against the top of the fitting.
Make sure you hold the fitting whilst unscrewing the switch otherwise you will end up bending the brake pipes!
Image
mike.perry
Series MM Registrar
Posts: 10183
Joined: Sun Jul 24, 2005 11:39 pm
Location: Reading
MMOC Member: No

Re: Brake light switch

Post by mike.perry »

If you have a spare foot available you can push very gently on the brake pedal as you tighten the switch, just to push any air out that might have got into the end of the pipe
[sig]3580[/sig]
alanworland
Minor Legend
Posts: 1453
Joined: Tue Jan 30, 2007 10:09 pm
Location: Essex
MMOC Member: No

Re: Brake light switch

Post by alanworland »

I found that the fluid just 'hovered' at the top of the fitting and as the switch was screwed in it just displaced the excess! Brill!
Image
Dean
Minor Legend
Posts: 2180
Joined: Fri May 30, 2008 9:41 pm
Location: Sutton Coldfield
MMOC Member: No

Re: Brake light switch

Post by Dean »

That's good to know Alan, thanks.
My Minor:
A Clarendon Grey 1953 4 Door Series II.
MMOC - 66535


bmcecosse
Minor Maniac
Posts: 46561
Joined: Wed Feb 16, 2005 11:24 pm
Location: ML9
MMOC Member: No

Re: Brake light switch

Post by bmcecosse »

Oh - I thought the kettle of water was for a nice cup of tea..........while the system self-bled ! :)
ImageImage
Image
Post Reply