bonnet motifs - gaskets?

Post by **wibble_puppy** » Wed Oct 15, 2008 9:26 am

when you fit your bonnet motif (badge and flash), should you put a thin gasket under them like you do the bonnet hinges?

wibble

Post by **alex_holden** » Wed Oct 15, 2008 9:40 am

I don't think so.

Post by **wibble_puppy** » Wed Oct 15, 2008 9:44 am

Post by **ferret76** » Wed Oct 15, 2008 11:27 am

I concur. Need gaskets under your bonnet hinges though.

Post by **ASL642** » Wed Oct 15, 2008 11:35 am

When we refitted the bonnet we bought some thin rubber matting off ebay and we now use this to make washers for all the chrome bits which stops them scratching the paint. You cannot buy rubber boot and bonnet washers now only paper. I think a metre cost £15 - enough for the fleet!

Post by **bmcecosse** » Wed Oct 15, 2008 6:23 pm

I suppose thin flexible plastic as sold by Ikea for kitchen cutting boards would do nicely - and being clear/translucent won't be obvious.

Post by **wibble_puppy** » Wed Oct 15, 2008 6:45 pm

bmcecosse wrote:I suppose thin flexible plastic as sold by Ikea for kitchen cutting boards would do nicely - and being clear/translucent won't be obvious.

Ah, clear plastic makes a lot of sense. Was trying to image the bonnet flash and badge with black gaskets like the hinges, and being unhappy

Post by **aupickup** » Wed Oct 15, 2008 6:49 pm

you will find i think that putting anything under the bonnet flash, that the back will not hook in the bonnet

Post by **wibble_puppy** » Wed Oct 15, 2008 6:58 pm

ah. Right ho. Thanks, dude

Post by **jock299** » Wed Oct 15, 2008 7:02 pm

Don’t shoot me down on this one as i know it has been abused in the past

but what about some clear silicone spread thinly and left to dry overnight off car stops metal against paint vibration

Post by **ASL642** » Wed Oct 15, 2008 7:02 pm

No the plastic is v. thin and by the time the bonnet hinge is bolted down is not at all visible. It is cut slightly smaller than the hinge so doesn't squeeze out. I know the chopping boards you mean and it is much thinner.

Post by **Luxobarge** » Wed Oct 15, 2008 7:13 pm

I've used bicycle inner-tube for this sort if thing before - nice and thin, and the rubber gives good paint protection. As it's black, the very thin line of black that will show if it's trimmed carefully looks fine on most body colours.

linearaudio · Post by **linearaudio** » Wed Oct 15, 2008 8:56 pm

For Gods sake don't be tempted to remove any excess gasket... with a stanley knife... in situ! Thats the sort of thing an eeijit like me does (surely, if I'm careful.....aaaargh!) I'm sure they modelled Dougal in Father Ted on me- I can just see how his "brain?" ticks!

Post by **callyspoy** » Wed Oct 15, 2008 10:49 pm

when i fitted the brake light into my boot motif i put bike inner tube as a gasket as there is a hole behind it now! it doesn't look too bad, but i would imagine clear plastic would be good for wibble...NOTHING CAN TAKE AWAY FROM THE VIBRANCY!

Post by **alainmoran** » Thu Oct 16, 2008 2:04 am

Umm ... dont use silicone sealant ... the plasticiser is made from acetic acid, which isnt very kind to paintwork ;)

Post by **wibble_puppy** » Thu Oct 16, 2008 4:19 am

thanks very much for all the excellent tips, everyone

Post by **Luxobarge** » Wed Oct 22, 2008 7:16 pm

This thread got me thinking - our bonnet mascot is a bit loose, and as it has no gaskets it's starting to damage the paint - so I took my own advice and made some out of bicycle inner tube!

First I touched up the slight paint damage, so it could dry.

Then I cut up some inner tube, and made a recess in a piece of wood for each end of the mascot, so it could sit with the mating surfaces flat on the wood. Then with a very sharp surgical scalpel I cut out a hole in the centre for the main mounting boss to poke through, then placed the mascot on the wood and cut around the edge of the mascot to precisely cut out the shape of the gasket.

Here you can see the block of wood with the recess cut in it, the scalpel and both the gaskets:

Here's the large end with the gasket fitted:

And the small end - this is a bit more fiddly but do-able:

I decided the small end might slip sideways when it's on, so I "glued" it down with some black silicone gasket sealant, and used a bit of masking tape to hold it there while it went off:

And here it is back on the car!

***Sorry about the rubbish photo quality!!***

it's really difficult to take close-ups with my camera, it doesn't want to focus properly! - Hopefully you get the idea.

The mascot now fits snugly with no movement, and you can hardly see the gaskets - just a very thin black line where it meets the bonnet. I'm sure it will now protect the paintwork too, especially as I use this as a handle to open and shut the bonnet, so it gets a bit of stress!

Hope this is of use/interest!

Cheers - Rick.

Post by **polo2k** » Wed Oct 22, 2008 7:25 pm

have a look on your camera for a button with a flower on it. This should be the macro mode, for shooting close up

Post by **Luxobarge** » Wed Oct 22, 2008 7:42 pm

polo2k wrote:have a look on your camera for a button with a flower on it. This should be the macro mode, for shooting close up

Found it! Nuts - I wish I'd known that before!

Many thanks - I'll remember that in future!

Cheers

Post by **wibble_puppy** » Wed Oct 22, 2008 7:51 pm

that's great work, rick, and looks to be an excellent result - now that you've found the macro setting on your camera, take a close-up of the mascot in situ

thank you for posting the account and pics of how you did it

am still pondering how to do mine - it's a van so the bonnet trim is different.

wibble xx