SADMOG (Sowf'ampton taawn)

Post by **paulk** » Sun Feb 17, 2008 5:37 pm

Well after we've sprayed Milly I might need a hand to pop the engine/gearbox in

Actually another question, Anyone got an original sidelight for a 59'. Doesn't matter if it's complete rubbish I just want to see one in the flesh to decide if I go down that route or just live with late ones.
I'm at a stage that if I want to fill in the wing hole and fit the right sidelights I need to do it now.

Post by **Peetee** » Wed Feb 20, 2008 8:19 am

Where to this week? Green dragon? Or did we decide that was too small?
Empress?

Post by **Rob_Jennings** » Wed Feb 20, 2008 11:18 am

lets stick with the empress

anyone about at the weekend? i need a hand to fit my half shafts....

Post by **Matt** » Wed Feb 20, 2008 6:12 pm

I may or may not be around for this week... im not sure yet

Post by **paulk** » Wed Feb 20, 2008 6:45 pm

Empress it is

Post by **Peetee** » Wed Feb 20, 2008 7:19 pm

Empress it is

"TAXI !" [waves arm]

Post by **Mike Shipman** » Wed Feb 20, 2008 8:03 pm

I hope to be there...

Post by **paulk** » Wed Feb 20, 2008 8:16 pm

Those of a nervous disposition look away now as the following pictures show a Minor being Dispatched and also a few blokes with Beards, Overalls and even flat caps.
You have been warned!!

Heres the piccys from The Sadmog meet in Ropley 2 weeks ago

Preperation is Important

Operating table ready

Getting stuck in

Do we need this bit?

Rob getting serious!

Sadmog at work

Front Suspension Masterclass

Heres what 5 blokes and 3 1/2 hours can do to a Minor!

Credits

Peetee, Rob Jennings, Matt, Dan Harris and Me

Post by **Peetee** » Wed Feb 20, 2008 10:42 pm

You know I reckon you could stick 4 pram wheels on that pallet and enter RIPMaude in the Goodwood Festival of Speed Soapbox Challenge.

Post by **d_harris** » Thu Feb 21, 2008 2:12 pm

Not coming tonight, Sorry guys

Post by **JimK** » Thu Feb 21, 2008 4:57 pm

Afternoon chaps,
I won't be around tonight - I'm busy in advance of two weeks teaching (Eindhoven next week) and the outlaws are down visiting.

Cheers,
Jim

Post by **Rob_Jennings** » Sun Feb 24, 2008 3:01 pm

yeah! Lizzy is back under her own power took a few hours but all back in one piece again and happy to go once round the block shaft was a bit of a mess but looked clean enough inside I'll bring the evidence with me on thursday

many thanks to Colin for handing me spanners most of the day and Peetee for the finishing touches

will be keeping close eye on new rear brakes, and flushing the diff oil in a few weeks to finish the job otherwise its a good'en

Post by **d_harris** » Sun Feb 24, 2008 3:54 pm

On the subject of not so working cars,, I got some stuff done to the trav today.

Finished plumbing the brakes apart from into the M/C because I want to get that out and have a look.

Cut out a whole load of rot from the inner arch and fabricated a new section and welded it in, then I was rained off

On this subject I stil have a fairly chunky bit to tidy up and re-weld - does anyone have an inner wing repair panel (with the captive nuts?) or a suitable piece of steel I can pinch (everything we have it a bit too flimsy...)

Edit: Paul, if Maude is around could I perhaps pinch that section? from the A pillar to the arch itself?

Post by **paulk** » Sun Feb 24, 2008 6:08 pm

Your welcome to it BUT it's a repair I did 2-3 Years ago so not exactly standard in its own right.

I need to get Maude cut up and gone by this weekend anyway so if you want anything shout now.

Post by **d_harris** » Sun Feb 24, 2008 6:57 pm

Paul,

Thats fine by me, at the moment I only have very flimsy or massivly thick steel so a "proper" panel is easily the best solution.

If you want some help cutting it out I will be around on Sunday

(its drivers side btw)

Post by **Rob_Jennings** » Tue Feb 26, 2008 9:44 am

Where to this week folks?

how about the white swan in Lyndhurst? or the oak inn at bank?

although Lizzy is up and running will no doubt be in the astra as the roads are still salt encrusted!

Post by **Matt** » Wed Feb 27, 2008 6:14 pm

I have some bits for Carlo... so hopefully he will turn up

I will be in the van so I dont really mind where

Post by **paulk** » Wed Feb 27, 2008 6:18 pm

Not bothered Where either.

Might be in the Van but still don't mind where.

Post by **Matt** » Wed Feb 27, 2008 8:02 pm

Oh... Paul I have something for you to play with, which I will bring

Post by **WPR678B** » Wed Feb 27, 2008 8:22 pm

Matt wrote:I have some bits for Carlo... so hopefully he will turn up

Yes, i am 99% sure i will be there (wherever that may be!) this week. Its been a while!