Photos wanted

[Keith]

Front view. No heater and one windscreen wiper.

[mrs.smith2012]

That’s perfect! Thank you!

[Mervin]

saloon ins right.JPG (208.31 KiB) Viewed 35935 times

saloon ins rear.JPG (236.76 KiB) Viewed 35935 times

saloon ins interior 1.JPG (266.28 KiB) Viewed 35935 times

saloon ins front.JPG (281.8 KiB) Viewed 35935 times

saloon ins engine.JPG (275.8 KiB) Viewed 35935 times

These were taken 14 years ago, but the car is still in my ownership and hardly changed. The Traveller, in the garage isn't mine.

[mrs.smith2012]

Ooh lovely photos! Thank you!

Is the car called Mervin?

[Mervin]

With a "Y", Mervyn. I haven't a clue why. It was named that when bought in 1999. I mistyped my username when registering for the 3rd or 4th time. My previous registrations (1st in 1999) timed out because of not posting enough.
Unfortunately that's an age related (SJ, Scottish) registration plate. The original was kept by the first owner. First registered in Blackpool.

[Bill_qaz]

Mervyn is a Welsh male name, maybe a former owner or family member.

[Owlsman]

With a "Y", Mervyn. I haven't a clue why. It was named that when bought in 1999. I mistyped my username when registering for the 3rd or 4th time. My previous registrations (1st in 1999) timed out because of not posting enough.
Unfortunately that's an age related (SJ, Scottish) registration plate. The original was kept by the first owner. First registered in Blackpool.

Beautiful looking car! I think it may be a Dual Personality Minor too. I've sent you a PM with a lot more information about the register.

Cheers,

Alan Smith (co-registrar of the MMOC Dual Personality register)

[Mervin]

"Mervyn is a Welsh male name, maybe a former owner or family member."
The previous owner lived in Chester, from where the car was bought. That's nearly in Wales.

[mrs.smith2012]

With a "Y", Mervyn. I haven't a clue why. It was named that when bought in 1999. I mistyped my username when registering for the 3rd or 4th time. My previous registrations (1st in 1999) timed out because of not posting enough.
Unfortunately that's an age related (SJ, Scottish) registration plate. The original was kept by the first owner. First registered in Blackpool.

Aah it’s nice that you’ve kept the name. I know many say it’s bad luck to change a car’s name… but I was quite set on my car being called Nellie before I even got her… so Daisy was rechristened

[Mervin]

saloon ins interior red highlight.jpg (267.86 KiB) Viewed 35331 times

Barely visible in the picture, but the slightly darker bit, it is faded gold in colour, circled, is a sticker from the original selling dealer in 1962.
"Supplied by" "Hadley Motors (St Annes) Ltd." "St Annes-On-The-Sea"

[svenedin]

saloon ins interior red highlight.jpg

Barely visible in the picture, but the slightly darker bit, it is faded gold in colour, circled, is a sticker from the original selling dealer in 1962.
"Supplied by" "Hadley Motors (St Annes) Ltd." "St Annes-On-The-Sea"

I like how you have mounted the additional gauges. That's discreet and tidy. Have you drilled through the metal of the parcel shelf bracket to mount these? I'm assuming the actual shelf material itself is not strong enough.

Stephen

[mrs.smith2012]

saloon ins interior red highlight.jpg

Barely visible in the picture, but the slightly darker bit, it is faded gold in colour, circled, is a sticker from the original selling dealer in 1962.
"Supplied by" "Hadley Motors (St Annes) Ltd." "St Annes-On-The-Sea"

Can I just confirm… Mervyn is 1962?

[Bill_qaz]

I did similar Stephen and picked up existing hole on metal edge.
But under glove box rather than shelf, as didn’t want to catch with leg getting in and out. Also routing capillary temp and copper pipe to oil gauge was easier above the shelf for me.

20220310_131723.jpg (1.63 MiB) Viewed 35245 times

[svenedin]

I did similar Stephen and picked up existing hole on metal edge.
But under glove box rather than shelf, as didn’t want to catch with leg getting in and out. Also routing capillary temp and copper pipe to oil gauge was easier above the shelf for me.
20220310_131723.jpg

Neat. When my car is back from paint I will have a good look at where I might be able to mount a single gauge. I like the combined oil pressure/water temperature Smiths gauges. What has prevented me from doing this for a long time is that the gauges are expensive and it is hard for me to work out where it will fit without actually having the gauge in my hand so to speak. Having spent a lot of money on a completely rebuilt engine just over a year ago, the last thing I want is to wreck the engine due to an oil leak on a long trip. On the other hand, the engine survived from new without any extra gauges. It would have to be capillary as the modern gauges don't like positive earth but I don't really want untidy capillary tube in the engine bay or the horror of having to drill holes in the bulkhead.......Talking myself out of it now!

Stephen

[les]

I’ve said it before, rightly or wrongly. I like the simplicity of the Minor, not being stressed out by gauge readings. Chill man !

[myoldjalopy]

I agree with Les. After all, you've been driving Xavier happily for around 36 years now without extra gauges, so why fit them now?!

[Mervin]

"Can I just confirm… Mervyn is 1962?" Yes, February 1962. There are alterations from the original. e.g. the sidelights, indicators and rear lights.

[Mervin]

"I'm assuming the actual shelf material itself is not strong enough."
Fortunately the shelf material is strong enough. The holes for the bracket nuts and bolts are very close to the support bar.
There are three gauges there now with the addition of a water temperature gauge.

[mrs.smith2012]

"Can I just confirm… Mervyn is 1962?" Yes, February 1962. There are alterations from the original. e.g. the sidelights, indicators and rear lights.

Excellent, thank you for confirming!

[Nickol]

To enhance the international aspect......

Morris in Amoeneburg.jpg (65.66 KiB) Viewed 34075 times

1969 Traveller , converted to LHD ca. 2016 - pictured in Amoeneburg.