A breathing question
Forum rules
By using this site, you agree to our rules. Please see: Terms of Use
By using this site, you agree to our rules. Please see: Terms of Use
A breathing question
No, not for me! My '62 4 x door has the breather set up as per the pic of my engine bay.
For the lack of something better to do, I smartened up the air filter box the other day, by stripping and respraying it. During the old paint removal, I noticed that the pipe/tube on the bottom plate of the air filter that connects to the rocker cover outlet via the short hose, was completely blocked up with paint. It took a while but I unblocked it eventually.
I'll freely admit that I don't understand how or why an engine 'breathes' but presumably, with the rocker cover hose effectively completely blocked off, it would be like me trying to inhale and exhale through a blocked nose. The car has been running well for some time but when I had a quick tootle round the block today, it did seem to be running particularly sweetly. It could be my imagination but would unblocking the hole in the air filter box make any perceptible difference to the way the engine runs? Also, why is it such a small hole anyway? Why not a simple open-ended pipe like on the rocker cover?
If possible, a short idiot's guide to engine breathing would be appreciated please. Thanks in advance.
For the lack of something better to do, I smartened up the air filter box the other day, by stripping and respraying it. During the old paint removal, I noticed that the pipe/tube on the bottom plate of the air filter that connects to the rocker cover outlet via the short hose, was completely blocked up with paint. It took a while but I unblocked it eventually.
I'll freely admit that I don't understand how or why an engine 'breathes' but presumably, with the rocker cover hose effectively completely blocked off, it would be like me trying to inhale and exhale through a blocked nose. The car has been running well for some time but when I had a quick tootle round the block today, it did seem to be running particularly sweetly. It could be my imagination but would unblocking the hole in the air filter box make any perceptible difference to the way the engine runs? Also, why is it such a small hole anyway? Why not a simple open-ended pipe like on the rocker cover?
If possible, a short idiot's guide to engine breathing would be appreciated please. Thanks in advance.
- Attachments
-
- IMG_20230821_171639198_MFNR.jpg (1.96 MiB) Viewed 2537 times
- svenedin
- Minor Legend
- Posts: 1960
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: A breathing question
What a very tidy engine bay. I notice you have the heater pipe on the manifold side. This is non-standard but means the thermostat can be changed without having to remove the pipe. There’s also a Hardi fuel pump pretending to be an SU with an SU sticker!
No engine has piston rings that make a perfect seal in the cylinder bore. This means that some of the gases from the combustion explosion get past the piston rings into the crankcase. This is called “blow-by”. One of the products of combustion is steam. Water is a bad thing to have in the oil. If there was no breathing system there would be “crankcase compression” (too much pressure in the crankcase) and the engine would tend to leak oil through the gaskets. The engine breathing system aims to relieve the crankcase compression and the oily fumes are fed into the inlet system and burnt in the engine.
Symptoms of a blocked breather system include oil leaks and “mayonnaise” (an emulsion of oil and water) in the rocker cover
Stephen
No engine has piston rings that make a perfect seal in the cylinder bore. This means that some of the gases from the combustion explosion get past the piston rings into the crankcase. This is called “blow-by”. One of the products of combustion is steam. Water is a bad thing to have in the oil. If there was no breathing system there would be “crankcase compression” (too much pressure in the crankcase) and the engine would tend to leak oil through the gaskets. The engine breathing system aims to relieve the crankcase compression and the oily fumes are fed into the inlet system and burnt in the engine.
Symptoms of a blocked breather system include oil leaks and “mayonnaise” (an emulsion of oil and water) in the rocker cover
Stephen
Last edited by svenedin on Mon Aug 21, 2023 8:24 pm, edited 1 time in total.
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
Re: A breathing question
You may also find, as I did, that sorting out the breather system reduces or even eliminates oil leaks you may have.
My traveller left a trail of oil not unlike the Torrey Canyon did in the 60s until the breather was sorted out.
My traveller left a trail of oil not unlike the Torrey Canyon did in the 60s until the breather was sorted out.
- svenedin
- Minor Legend
- Posts: 1960
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: A breathing question
Mine too!
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
-
- Minor Fan
- Posts: 254
- Joined: Tue Oct 26, 2010 9:01 pm
- MMOC Member: No
Re: A breathing question
My Traveller was the same until I unblocked the rubber breather tube. I could not believe the amount of gunk that a small tube could hold. I swear the car ran sweeter afterword too. Beautiful engine by the way.
1969 Traveller in Almond green. Owned since 1979.
-
- Minor Maniac
- Posts: 10879
- Joined: Thu Jul 19, 2012 12:05 pm
- Location: Hampshire
- MMOC Member: Yes
Re: A breathing question
The heater return pipe over the manifold is standard. Part No: ACA5514 (MOSS).
There were other variations to the heater return pipe including one that went over the top of the thermostat housing as stated above.
There were other variations to the heater return pipe including one that went over the top of the thermostat housing as stated above.
- Bill_qaz
- Minor Addict
- Posts: 702
- Joined: Fri Jan 14, 2022 7:31 pm
- Location: Oxfordshire
- MMOC Member: Yes
Re: A breathing question
Mine is same 1962 and the heater pipe runs the same, why do you think it's none standard?svenedin wrote: ↑Mon Aug 21, 2023 8:14 pm What a very tidy engine bay. I notice you have the heater pipe on the manifold side. This is non-standard but means the thermostat can be changed without having to remove the pipe. There’s also a Hardi fuel pump pretending to be an SU with an SU sticker!
No engine has piston rings that make a perfect seal in the cylinder bore. This means that some of the gases from the combustion explosion get past the piston rings into the crankcase. This is called “blow-by”. One of the products of combustion is steam. Water is a bad thing to have in the oil. If there was no breathing system there would be “crankcase compression” (too much pressure in the crankcase) and the engine would tend to leak oil through the gaskets. The engine breathing system aims to relieve the crankcase compression and the oily fumes are fed into the inlet system and burnt in the engine.
Symptoms of a blocked breather system include oil leaks and “mayonnaise” (an emulsion of oil and water) in the rocker cover
Stephen
The pipe from the air filter let's air into the rocker cover and the crankcase breathes out of the pipe on exhaust side of engine and I believe you should have a none vented oil cap.
You pipe is infront of your carburettor so the air intake is by the exhaust manifold for winter. You can pivot to point forward for summer use.
Last edited by Bill_qaz on Mon Aug 21, 2023 8:50 pm, edited 1 time in total.
Regards Bill
-
- Minor Legend
- Posts: 2558
- Joined: Tue Jan 29, 2013 10:32 pm
- Location: Kernow
- MMOC Member: Yes
Re: A breathing question
I prefer the older arrangement where the heater hose runs from the bottom of the rad along the engine bay floor and up into the bulkhead. Not in the way of anything
- svenedin
- Minor Legend
- Posts: 1960
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: A breathing question
Fair enough. I’ve never seen the heater pipe on the manifold side, only on the other side. With my engine and manifold the pipe could not be routed on the manifold side. Incidentally, how is the heater warning plate held to the pipe?philthehill wrote: ↑Mon Aug 21, 2023 8:42 pm The heater return pipe over the manifold is standard. Part No: ACA5514 (MOSS).
There were other variations to the heater return pipe including one that went over the top of the thermostat housing as stated above.
Last edited by svenedin on Mon Aug 21, 2023 9:09 pm, edited 2 times in total.
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
- Bill_qaz
- Minor Addict
- Posts: 702
- Joined: Fri Jan 14, 2022 7:31 pm
- Location: Oxfordshire
- MMOC Member: Yes
Re: A breathing question
Bill_qaz wrote: ↑Mon Aug 21, 2023 8:46 pmMine is same 1962 and the heater pipe runs the same, why do you think it's none standard?svenedin wrote: ↑Mon Aug 21, 2023 8:14 pm What a very tidy engine bay. I notice you have the heater pipe on the manifold side. This is non-standard but means the thermostat can be changed without having to remove the pipe. There’s also a Hardi fuel pump pretending to be an SU with an SU sticker!
No engine has piston rings that make a perfect seal in the cylinder bore. This means that some of the gases from the combustion explosion get past the piston rings into the crankcase. This is called “blow-by”. One of the products of combustion is steam. Water is a bad thing to have in the oil. If there was no breathing system there would be “crankcase compression” (too much pressure in the crankcase) and the engine would tend to leak oil through the gaskets. The engine breathing system aims to relieve the crankcase compression and the oily fumes are fed into the inlet system and burnt in the engine.
Symptoms of a blocked breather system include oil leaks and “mayonnaise” (an emulsion of oil and water) in the rocker cover
Stephen
The pipe from the air filter let's air into the rocker cover and the crankcase breathes out of the pipe on exhaust side of engine and I believe you should have a none vented oil cap.The fumes are not drawn into the air intake.
You pipe is infront of your carburettor so the air intake is by the exhaust manifold for winter. You can pivot to point forward for summer use.
20230622_155213.jpg
Regards Bill
Re: A breathing question
Thanks all, for your responses. I'm breathing a lot easier now.......as is the car!!
Why is the hole so small on the air filter base plate though, if as seems likely, it can easily get blocked up?
My engine does drip a bit of oil but I wouldn't say excessively so. I'll have to put a clean piece of cardboard on the garage floor and see if there is any difference, post unblocked breather!
Re the summer/winter settings for the air filter box - do I simply turn it a full 180°?
Well spotted, Stephen - the fuel pump is indeed an electronic jobbie but identifying as something quite different. Nowadays all the rage and quite acceptable in some circles, I hear!
The 'Caution' warning plate is held on the copper section of the heater pipe by 2 spring clips riveted through the plate.
Thanks again for all your replies.
Why is the hole so small on the air filter base plate though, if as seems likely, it can easily get blocked up?
My engine does drip a bit of oil but I wouldn't say excessively so. I'll have to put a clean piece of cardboard on the garage floor and see if there is any difference, post unblocked breather!
Re the summer/winter settings for the air filter box - do I simply turn it a full 180°?
Well spotted, Stephen - the fuel pump is indeed an electronic jobbie but identifying as something quite different. Nowadays all the rage and quite acceptable in some circles, I hear!
The 'Caution' warning plate is held on the copper section of the heater pipe by 2 spring clips riveted through the plate.
Thanks again for all your replies.
- svenedin
- Minor Legend
- Posts: 1960
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: A breathing question
It’s a metal plate that cautions that the heater cannot be completely drained and that antifreeze should used. It’s just an original detail I would like to have.
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
- Bill_qaz
- Minor Addict
- Posts: 702
- Joined: Fri Jan 14, 2022 7:31 pm
- Location: Oxfordshire
- MMOC Member: Yes
Re: A breathing question
Owlsman wrote: ↑Mon Aug 21, 2023 9:44 pm Thanks all, for your responses. I'm breathing a lot easier now.......as is the car!!
Re the summer/winter settings for the air filter box - do I simply turn it a full 180°?
. [/quote
If you zoom in you can see the inlet is just under the float bowl of the carburettor so not quite 180 degrees ]
Last edited by Bill_qaz on Mon Aug 21, 2023 10:50 pm, edited 2 times in total.
Regards Bill
- Bill_qaz
- Minor Addict
- Posts: 702
- Joined: Fri Jan 14, 2022 7:31 pm
- Location: Oxfordshire
- MMOC Member: Yes
Re: A breathing question
Regards Bill
Re: A breathing question
You can see it on my engine here. I took the photo on collection day so no comments about cleanliness are necessary!
1961 Morris Minor 1000
- svenedin
- Minor Legend
- Posts: 1960
- Joined: Fri Aug 29, 2014 9:27 am
- Location: Surrey
- MMOC Member: Yes
Re: A breathing question
Thank you. Does the warning sign/plate/badge have a backing plate or are the clips riveted directly to the badge? Terry clips and a badge are easy enough to buy but if there’s a backing plate that would be tricky to find although not difficult to make.
Stephen
1969 1098cc Convertible “Xavier” which I have owned since 1989.
Stephen
Stephen
Re: A breathing question
It's got a couple of clips riveted to the backside of it that just pop over the pipe. It's been in the ultrasonic cleaner along with the pipe and plenty of other parts and look pretty good now.svenedin wrote: ↑Tue Aug 22, 2023 7:18 amThank you. Does the warning sign/plate/badge have a backing plate or are the clips riveted directly to the badge? Terry clips and a badge are easy enough to buy but if there’s a backing plate that would be tricky to find although not difficult to make.
Stephen
1961 Morris Minor 1000