Search found 8 matches

by riley 1489
Sun Jan 15, 2012 11:02 am
Forum: Electrical
Topic: Argumentative grandad over headlamps
Replies: 16
Views: 3230

Re: Argumentative grandad over headlamps

Not sure if that's a specific / special Cibie light you have in mind there BMC but I've just had a quick Google & new 7" Cibie H4 headlamp conversions are still available for circa £35 each at various race / rally type specialists.

Chris
by riley 1489
Sat Jan 14, 2012 1:28 pm
Forum: Electrical
Topic: Argumentative grandad over headlamps
Replies: 16
Views: 3230

Re: Argumentative grandad over headlamps

Well Cibies used to be more cost effective in the long run as the reflectors don't rust (had ones on my Midget & MGBGTV8 for 25+ years). I would be interested to see the 'test' referred to as the Cibie beam pattern is very good indeed. I think they're about £80 a pair. I had a look at Lucas H4 h...
by riley 1489
Sat Jan 14, 2012 11:37 am
Forum: Electrical
Topic: Argumentative grandad over headlamps
Replies: 16
Views: 3230

Re: Argumentative grandad over headlamps

There was a test on sealed beams for classics and wipac came out on top with there quadoptic range and like Mike says they are now coated. Good news they have fixed the rusting problem. I remember replacing a few for that reason in the past. Where was that test, I'd be interested in searching that ...
by riley 1489
Fri Jan 13, 2012 8:48 pm
Forum: Electrical
Topic: Argumentative grandad over headlamps
Replies: 16
Views: 3230

Re: Argumentative grandad over headlamps

Hi, I converted my sealed beams to halogen- using Cibie units. Much better quality than Wipac which tend to rust on the reflectors. More expensive but you get what you pay for- much better beam pattern too. Thus the headlights on my Riley 1.5 and MG Midget are just as good as those on my modern BMW ...
by riley 1489
Fri Jan 13, 2012 8:30 pm
Forum: Mechanical
Topic: engine revs when depressing the clutch pedal
Replies: 16
Views: 5131

Re: engine revs when depressing the clutch pedal

Carbon bearing:[frame]Image[/frame]

Roller bearing:[frame]Image[/frame]
by riley 1489
Fri Jan 13, 2012 8:24 pm
Forum: Mechanical
Topic: engine revs when depressing the clutch pedal
Replies: 16
Views: 5131

Re: engine revs when depressing the clutch pedal

Hi all, I have had my 1275cc MG Midget since 1980 and have never worn out a carbon release bearing, I think I have changed the whole clutch once in 32 years / 120k plus miles. BUT when I build up my 'new' MG Midget I will probably convert to roller bearing due to my positive experience of installing...
by riley 1489
Sun Dec 18, 2011 11:11 am
Forum: Off-Topic
Topic: French Polishing
Replies: 4
Views: 1375

Re: French Polishing

Hi, I used the Rustins clear plastic coating after reading an article about it in Practical Classics, they did a feature on Chapman & Cliff, run by ex Rolls Royce employees who restore automotive woodwork. This is close to or maybe the same as the original finish. It wasn't originally french pol...
by riley 1489
Fri Dec 16, 2011 5:01 pm
Forum: Off-Topic
Topic: French Polishing
Replies: 4
Views: 1375

Re: French Polishing

Hi Matt, Yes done my own Riley 1.5 dashboard recently! As the veneer was OK I carefully stripped off the laquer with a heat gun and a blunt scraper. Nitromors would not touch it. I then refinished it with Rustins 2-pack Plastic Coating, as recommended in a feature in Practical Classics about a year ...